mr fixit
Jim Dempsey posted an answer for this Copystar CS6030 1-TK659 Standard Black Toner 0T2FB0CS:
"Fuser etror check for paper jams in fuset snd remove as nd tufn off and on to reset,or..."
Jim Dempsey posted an answer for this Kyocera Office Equipment & Supplies:
"1087 1087 then 163 reset it may prompt to turn off and on again, if that does not reset..."
Jim Dempsey posted an answer for this Kyocera Office Equipment & Supplies:
"you can buy on at any walmart."
Jim Dempsey posted an answer for this Kyocera Office Equipment & Supplies:
"fuser error ,1087 1087 , then 163 reset ,may be prompted to turn off and on again. if it..."
Jim Dempsey posted an answer for this Kyocera FS4020DN (A4) Workgroup Mono Laser (Duplex+Networked) 128MB 1200dpi 45ppm 600 Sheet Printer:
"No transfer charging. Poor contact of engine PWB's transfer bias output terminal and..."
Jim Dempsey posted an answer for this Kyocera Office Equipment & Supplies:
"you need to replace maintenance kit c MK-8505C (Maintenance Kit) 1702LC0UN2 300K $400.00..."
Jim Dempsey posted an answer for this Kyocera Office Equipment & Supplies:
"press numeric keys 1087 1087 , then 251 Checking/clearing the maintenance count..."
Jim Dempsey posted an answer for this Kyocera Office Equipment & Supplies:
"7410 Drum unit non- installing error The drum unit is not installed or not installed..."
Jim Dempsey posted an answer for this Kyocera FS-1118MFP Laser Printer:
"Press the system menu/counter key,Select Service setting using the up/down cursor..."
Jim Dempsey posted an answer for this Kyocera Mita Drum Cleaning Blade Km 1620 1635 1650 Km2020 Km2035 Km2050 2c918010:
"1. No transfer charging. A. The connector terminals of the high-voltage PCB make poor..."
Jim Dempsey posted an answer for this Kyocera Office Equipment & Supplies:
"1087 1087, then 163 and press print button. then exicute and print button, you may be..."
Jim Dempsey posted an answer for this Kyocera Kyo1t02kh0us0 Br Taskalfa 180 1tk437 Sd Black Toner Kyocera:
"from key pad press 1087 1087, the copier will go to maintenance mode ,press 163 then print..."
Jim Dempsey posted an answer for this Kyocera FS-1135MFP:
"key in 1087 1087 to get to maintenance mode, then 251 to reset maintenance count , then..."
Jim Dempsey posted an answer for this Kyocera Mita Drum Cleaning Blade Km 1620 1635 1650 Km2020 Km2035 Km2050 2c918010:
"A C4200 IS A BAD LASER UNIT , EXPENSIVE REPAIR FOR A COPIER THAT OLD."
Jim Dempsey posted an answer for this Kyocera Mita KM-1620 Toner Black 370AM010001:
"C4200 CODE IS FOR A LASER UNIT PROBLEM, IF IT WONT RESET BY TURNING IT OFF AND ON THE..."
Jim Dempsey posted an answer for this Kyocera FS-6025MFP Laser Multifunction Printer - Monochrome - Plain Pa:
"YOU CAN SCAN TO A USB FLASH DRIVE ,THEN LOAD IT IN YOUR COMPUTER."
Jim Dempsey posted an answer for this Kyocera Fs-1300d Printer:
"your question is not specific enough, be more presise of what the problem is!!"
Jim Dempsey posted an answer for this Kyocera Office Equipment & Supplies:
"you can go into service mode by pressing 1087 twice ,then 163 and reset fuser error ,it my..."
Jim Dempsey posted an answer for this Kyocera FS-1135MFP:
"you need additional memory for the fax or scanner for scanning large files."
Jim Dempsey posted an answer for this Kyocera Mita KM 1510 Laser Printer:
"4 Slide the toner container to the left and then pull it out toward you. 5 Gently pull the..."
Jim Dempsey posted an answer for this Kyocera Mita KM 1510 Laser Printer:
"Toner is being replenished inside the copier. Wait a few minutes. * Although the lamp..."
Jim Dempsey posted an answer for this Kyocera FS-6025MFP Laser Multifunction Printer - Monochrome - Plain Pa:
"Check the scanner lock,it is used when the copier is being transported,it may be in the..."
Jim Dempsey posted an answer for this Copystar CS-2050 All-In-One Printer:
"needs cleaning and drum and fuser replaced, to reset maintenance counter sim u251 press..."
Jim Dempsey posted an answer for this Kyocera Office Equipment & Supplies:
"serial # on right side cover above off/on switch"
Jim Dempsey posted an answer for this Copystar CS-2050 All-In-One Printer:
"http://usa.copystar.com/americas/jsp/Kyocera/download..."
Jim Dempsey posted an answer for this Copystar CS-2050 All-In-One Printer:
"LOAD EVVELOPE IN MP TRAY ON SIDE OF COPIER AND CHANGE THE SETTING TO ENVELOPES FOR MP TRAY"
Jim Dempsey posted an answer for this Copystar CS-2050 All-In-One Printer:
"http://usa.copystar.com/americas/jsp/Kyocera/download..."
Jim Dempsey posted an answer for this Copystar CS-2050 All-In-One Printer:
"laser unit is under cover where copies exit, remove cover unplug laser unit and then..."
Jim Dempsey posted an answer for this Copystar CS-2050 All-In-One Printer:
"press 1087 twice and enter maintenance mode, press 251 and reset to 0"
Jim Dempsey posted an answer for this Copystar CS-2050 All-In-One Printer:
"press 1087 twice, enter maintence mode press 251 and reset to 0"
Jim Dempsey posted an answer for this Copystar CS-2050 All-In-One Printer:
"C4000 Polygon motor synchronization problem The polygon motor does not reach the stable..."