Sewing Machine Repair
Jimmie Sill posted an answer for this Brother LS2125i Sewing Machine:
"The total plastic cover on both sides must be removed. Behind the shuttle their is a..."
Jimmie Sill posted an answer for this PfaFF Sewing Machines:
"The grease that is their may be thick. Get your hair dryer out and warm the total parts..."
Jimmie Sill posted an answer for this Kenmore Sewing Machines:
"If your transformer is shorted somehow it could get very hot. This would also cause a..."
Jimmie Sill posted an answer for this Juki Sewing Machines:
"The tension on the belt is probably too tight. This would keep the motor from turning the..."
Jimmie Sill posted an answer for this Janome Sewing Machines:
"It is a good idea to take the bobbin out and turn the hand wheel. Monitor the turning hook..."
Jimmie Sill posted an answer for this Sewing Machines:
"Some machines have a switch for high or low speed."
Jimmie Sill posted an answer for this Singer 1120 Mechanical Sewing Machine:
"If the bobbin case(holds bobbin) fell apart due to force it is likely needing to be..."
Jimmie Sill posted an answer for this Sewing Machines:
"Your gears are needing replaced. They're the gears that make the hook (metal piece) move."
Jimmie Sill posted an answer for this Sewing Machines:
"The small wheel on the side of the hand wheel may not be engaged. If it still doesn't work..."
Jimmie Sill posted an answer for this Baby Lock Sewing Machines:
"I would start with looking to see if the needle bar is loose and is not moving as a..."
Jimmie Sill posted an answer for this Sewing Machines:
"Try to increase the upper tension. Try with your fingers to pull the thread to see if the..."
Jimmie Sill posted an answer for this Sewing Machines:
"I wouldn't try to. The voltage and current for these are usually different. Your book..."
Jimmie Sill posted an answer for this White Sewing Sewing Machines:
"Most likely the grease used has gotten hard. Take off the top and use your hair dryer to..."
Jimmie Sill posted an answer for this Sewing Machines:
"Your foot pedal sounds like it needs to be repaired or replaced."
Jimmie Sill posted an answer for this Sewing Machines:
"Your foot pedal needs to be fixed or replaced."
Jimmie Sill posted an answer for this Sewing Machines:
"Try to get your needle loose and out. Check for a mess of thread. Once for sure..."
Jimmie Sill posted an answer for this Janome Sewing Machines:
"1. Thin material needs backing. 2. Lower foot pressure. 3. Adjust top tension to..."
Jimmie Sill posted an answer for this Sewing Machines:
"Set top tension at four. If the ball of thread remains on bottom then loosen the bobbin..."
Jimmie Sill posted an answer for this Necchi Sewing Machines:
"Check here. Results are usually good. Sewing Parts Online"
Jimmie Sill posted an answer for this Sewing Machines:
"Replace the needle first. Use your straight stitch and try sewing with the needle to the..."
Jimmie Sill posted an answer for this Sewing Machines:
"If you don't get your needle inserted all the way it will react the same as if your..."
Jimmie Sill posted an answer for this White Sewing Sewing Machines:
"While turning the handwheel towards you monitor the needle when it begins to rise. Look..."
Jimmie Sill posted an answer for this Sewing Machines:
"The bobbin winder has a tire on the opposite part of the machine (inside). If it is..."
Jimmie Sill posted an answer for this Singer Sewing Machines:
"Your motor has a couple of screws to hold the tension on the belt. Loosen them and pull..."
Jimmie Sill posted an answer for this PfaFF Sewing Machines:
"I would first try to use another foot control before anything else."
Jimmie Sill posted an answer for this Singer Sewing Machines:
"For the tension to move at all the foot has to be down. If the tension isn't functioning..."
Jimmie Sill posted an answer for this Baby Lock Sewing Machines:
"Try rethreading it using the order: 3, 4, 2, 1. If you are threading it in the wrong..."
Jimmie Sill posted an answer for this Sewing Machines:
"Go to Singer Parts: Singer Parts Online.....You can look for the embroidery unit on one of..."
Jimmie Sill posted an answer for this Juki Sewing Machines:
"Set the top tension to four. Now, if the bottom seems too loose go ahead and loosen the..."
Jimmie Sill posted an answer for this Bernina Artista 180:
"I'm not real familiar with this issue but my first thought is the format of the program is..."
Jimmie Sill posted an answer for this PfaFF Sewing Machines:
"Pfaff sewing machines are difficult to repair in most cases but you can try if you like. ..."