1
Jarratt posted an answer for this Fujitsu Office Equipment & Supplies:
"Motor fuse alarm. looks like you need a new main board."
Jarratt
Jarratt posted an answer for this Fujitsu fi-5120C:
"I have a Fujitsu fi-5120C with ScandALL V1.8.1, installed on Windows XP. When scanning..."
JarrattJarratt posted an answer for this Fujitsu fi-5120C:
"hi, it sounds like the scanner is multifeeding, and as you have it set to A4 once..."
Jarratt
Jarratt posted an answer for this Canon DR-3080CII Path-Through Flatbed Scanner:
"Having multiples feed even after replacing roller kit, If i put a little preasure on the..."
JarrattJarratt posted an answer for this Canon DR-3080CII Path-Through Flatbed Scanner:
"Try rotating the sep roller backwards to reset the planetary gear. if that dont work..."
JarrattJarratt posted an answer for this Canon DR-3080CII Path-Through Flatbed Scanner:
"Who to replace rollers?"
JarrattJarratt posted an answer for this Canon DR-3080CII Path-Through Flatbed Scanner:
"hi. the rollers on this scanner needs to be replaced by an engineer. Try paralogic..."
Jarratt
Jarratt posted an answer for this Panasonic KV S2026C Path-Through Scanner:
"This one is easy, its yoru exit sensor, the only sensor in the scanner "looking" up, so..."
Jarratt
Jarratt posted an answer for this Kodak i30 Path-Through Scanner:
"1- face down sd ram failure 2 face up dram failure 3 cpu dram failure"
Jarratt
Jarratt posted an answer for this Canon DR-9080C Path-Through Scanner:
"Hi what size page are you trying to scan, if they are smaller than the gap between the..."
JarrattJarratt posted an answer for this Kodak Office Equipment & Supplies:
"What does the KDS Log say? find it in the SVT info tab and save it for more info. its..."
Jarratt
Jarratt posted an answer for this Fujitsu fi-5530C Scanner:
"You have a rear optical error. check the lamp is lighting.... open the ADF and push in the..."
Jarratt
Jarratt posted an answer for this Panasonic KV-S1025C:
"Are you trying to clear the page count that tells you, you need to replace rollers etc?..."
JarrattJarratt posted an answer for this Fujitsu fi-5530C Scanner:
"P is it warming up. if its not going from that, it may think the cover is open, try..."
JarrattJarratt posted an answer for this Fujitsu fi-5120C:
"The plastic around the exit rollers may have come unclipped from the base, the exit..."
Jarratt
Jarratt posted an answer for this Bell & Howell FB Series 2000D Flatbed Scanner:
"Hi, It may be the clutch on the left side of the ADF. there are 2 there, one does the pick..."
Jarratt
Jarratt posted an answer for this Fujitsu fi-4530C Pass-Through Scanner:
"Hi F at power on is a ROM Error. sounds like a main board issue. check for dry joints, but..."
Jarratt
Jarratt posted an answer for this Fujitsu fi-5750C Flatbed Scanner:
"these rear camers get the board that has the CCD chip on it come loose from the camera...."
Jarratt
Jarratt posted an answer for this Fujitsu fi-4750C Flatbed Scanner:
"This is usually a main board fault. re solder the legs of the 2 sets of the 3 transistors..."
Jarratt
Jarratt posted a question about ASUS A8N-SLI Deluxe Motherboard:
"Hi I had a problem where i needed the cpu seat for this motherboard. which someone..."
JarrattJarratt posted a question about ASUS A8N-SLI Deluxe Motherboard:
"I have broken the CPU seat, the bit of plastic that is screwed to the motherboard around..."
Jarratt
Office Equipment &... 16 answers
