1Sometimes the solution IS easy!
Asmodius posted an answer for this Husqvarna Sewing Machines:
"The middle dial (stitch length), push the center button in and it reverses."
Asmodius
Asmodius posted an answer for this Suzuki Motorcycles:
"I've had a similar problem, because I blocked too many of the 'emissions' vents. In my..."
AsmodiusAsmodius posted an answer for this Sewing Machines:
"I lost the manual. When I try to sew the needle thread keeps breaking. It will pick it up..."
AsmodiusAsmodius posted an answer for this Sewing Machines:
"Remove the needle. The flat of the needle goes toward the back of the machine, make sure..."
AsmodiusAsmodius posted an answer for this PfaFF Sewing Machines:
"The machine is binding up. Very slow."
AsmodiusAsmodius posted an answer for this PfaFF Sewing Machines:
"Unhook the handwheel clutch (silver knob turn toward you, inside the handwheel). It should..."
AsmodiusAsmodius posted an answer for this PfaFF Sewing Machines:
"what year was the pfaff 294 serial no 30467931 manufactured"
AsmodiusAsmodius posted an answer for this PfaFF Sewing Machines:
"1973 Source: see below http://www.ismacs.net/pfaff/pfaff_manufacture_dates.html"
AsmodiusAsmodius posted an answer for this Sewing Machines:
"Place the bobbin flat on the table with the thread winding clockwise (comes off the top of..."
AsmodiusAsmodius posted an answer for this Sewing Machines:
"how do i thread the bobbin on my sewing machine if it doesnt feed properley"
Asmodius
Asmodius posted an answer for this 1998 BMW R 1200 C:
"How do you replace the Battery on a R1200C?"
AsmodiusAsmodius posted an answer for this 1998 BMW R 1200 C:
"Most BMW's are replaced from under the seat. Lift the seat, pull out the tray, unhook the..."
Asmodius
Asmodius posted an answer for this Delta 36 977 Left Tilt Contractors Saw:
"Need to adjust Miter gauge for Delta tablesaw 36-977. The 90 degree stop is off"
AsmodiusAsmodius posted an answer for this Delta 36 977 Left Tilt Contractors Saw:
"1) Before setting the Miter gauge, check that the blade is straight (parallel) with the..."
Asmodius
Asmodius posted an answer for this Saws:
"how do i change the blade"
AsmodiusAsmodius posted an answer for this Saws:
"1) unplug the saw 2) raise the blade completely 3) remove the "throat plate" so you can..."
Asmodius
Asmodius posted an answer for this JVC Everio GZ-MG27 Camcorder:
"cannot get video files from cam to final cut pro on mac"
AsmodiusAsmodius posted an answer for this JVC Everio GZ-MG27 Camcorder:
"IF you have the USB cable connected and can see the files, like another drive, then you..."
AsmodiusAsmodius posted an answer for this PfaFF Creative 7570:
"pfaff 360 automatic slows and stops after only minutes of use"
AsmodiusAsmodius posted an answer for this PfaFF Creative 7570:
"Pfaff 360's don't like to sit, they like to drink. . .. oil. Set top knob "C" to 0 Right..."
Asmodius
Asmodius posted an answer for this Singer 7462 Mechanical Sewing Machine:
"PFAFF 362 Sewing Machine: The shift lever to move from straight stitch to zigzag stitch..."
AsmodiusAsmodius posted an answer for this Singer 7462 Mechanical Sewing Machine:
"Remove the top cover (grasp and lift straight up), spray with "Tri-Flow, liberally inside...."
Asmodius
Sewing Machines 7 answers
Saws 2 answers
Motorcycles 2 answers
Video Cameras 1 answer
