Zanussi Washing Machines - Recent Questions, Troubleshooting & Support


broken circuit in printed circuit board

Zanussi Washing... | Answered on Sep 16, 2019


Hi.
This sounds like doorlock issue.
You can access it from the door panel.
Panel has 4-6 screws.
From there you can check it with a multimeter (ohm setting).
It could also be as simple as bent door hatch, door lock not engaging with doorlock.

Zanussi Washing... | Answered on Sep 10, 2019


If the washer won't drain there might be a clogged pump or hose. It's common for small socks or other small clothing items to get into the water drain system and clog the hose leading to the pump or the pump itself. Remove the hoses from the pump in order to remove the article of clothing.

Zanussi Washing... | Answered on Jun 29, 2019


E20 means problem with drain water phase
Only two things need to be checked:

- Drain pump could be clogged or no power supply (the last means
faulty drain pump, faulty electronic or wiring between drain pump
and electronic.
- Your home drainage system (in the wall) is clogged (This is very
easy to check visually, disconnect the drain hose from your
siphon and put water in some container or in washbasin.)

Dado

Zanussi Washing... | Answered on Jun 15, 2019


Highly unlikely any damage will have been done so long as it hasnt been in use for a long time (weeks).

In a front loading washing machine, most of the mechanicals inside are held between springs at the top and dampers at the bottom. The transit bolts are used to minimse how much movement can ocour whilst the machine is in transit as excessive movement could damage the springs/dampers. When they are removed, normal movement of the mechanicals helps keep the machine stable and minmises vibration.

So, the worst that happens when the machine is used with the transit bolts in place is it vibrates alot, and possible moves about.

Remove the bolts as soon as possible and it should be fine.

Zanussi ZWF12070... | Answered on May 23, 2019


Hello,
E30 can be a faulty pressure switch,Heating element earth fault or the main P.C.B.(Programmer).Does the machine fill with water then empty.
Most common fault is the heating element,once this is replaced it should cure the fault.

Zanussi ZWF1430W... | Answered on May 19, 2019


Don't know model# try utbe
image-km53jp5dlkz0ffzm4tt5u4mo-5-20.jpg

image-km53jp5dlkz0ffzm4tt5u4mo-5-27.jpg

Zanussi Washing... | Answered on Mar 02, 2019


Page 9 of this manual, if this is the same model, may help turn off acoustic signals. It shows an image of a P and another image of a button to turn off.

https://manuall.co.uk/zanussi-zwf-91483-wr-lindo-300-washing-machine/

Zanussi Washing... | Answered on Feb 23, 2019


This is not a real solution because it is impractical. But it may work. The machine has different sensor. One or more and not receiving the proper signals. Some sensors are like push in buttons. If they are not pressed the machine won't work or will just jump to end cycle. Since you mentioned it does works when you move the machine. It indicates a sensor may be loosen the drum bounces and when cloth is unevenly distributed it hits hard and the machine makes loud noises BUMP BUMP so my theory is a sensor is loosen and needs to be reattach . Only do it yourself if you have some experience taking things apart. Good luck. Anyways my impractical solution was to put two pieces of wood in only 2 of the 4 corners of washer and trying it this way the drum will be tilt and has more chances of pressing sensor.

Zanussi zwh6160p | Answered on Feb 17, 2019


WE COULD NEVER TELL YOU IF IT IS WORTH FIXING . ONLY YOU KNOW HOW OLD IT IS AND IF YOU WANT TO WASTE MONEY FIXING OLD THINGS

Zanussi Washing... | Answered on Feb 16, 2019


Here is a video just for you...
https://youtu.be/TQCmW2j432A

Zanussi Tricity... | Answered on Feb 08, 2019


This can be due to error in the control board. Shut down and remove plug and when switched on press down the start/stop button. If the error does not clear this can be a fault in the motor drive within the control panel board.
Remove the panel and check the connections to the motor, check the motor and the capacitor to the motor or if the motor is jammed.

Zanussi Washing... | Answered on Feb 03, 2019

Not finding what you are looking for?
Zanussi Logo

3,319 questions posted

Ask a Question

Usually answered in minutes!

Top Zanussi Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

peter gittos
peter gittos

Level 2 Expert

247 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a Zanussi Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...