Whirlpool Washing Machines - Page 4 - Recent Questions, Troubleshooting & Support

Did you try a power reset? Remove the mains plug overnight. It will reset the electronic mainboard. Normally, they spin or they don't. https://www.google.com/search?q=Whirlpool+wfw75hefw+not+spinning+on+program ..

Check the drain pump, but your error code is the door lock.

F5 E3 Error Code for Top Load Washer

Whirlpool https://producthelp.whirlpool.com > ... > F# E# or F## Apr 5, 2021 - The F5 E3 alert indicates there is issue with the lid lock. Do not force the lid open, as permanent damage could occur. Remove any objects from ... ‎Possible Solutions · ‎Did you receive a F5 E3 lid...

F5 E3 - Front Load Washer - Product Help

Whirlpool https://producthelp.whirlpool.ca > ... > F5 E3 This error code indicates that the door is not locking properly. Is the door firmly closed? The door must be completely closed for the washer to operate. The ...

WHIRLPOOL CABRIO WASHER ERROR F5E3 EXPLAINED

appliancerepairguides.com https://appliancerepairguides.com > whirlpool-cabrio-... Apr 4, 2017 - The Cabrio Washer F5E3 error code means the lid lock will not unlock or the lock assembly has failed. This error can happen if there is anything ...

Quite simply you locate the leak and replace the hoses, gaskets or the part that is leaking. A trick is to slip some paper under it and pull it out after a few minutes to see the area of the leak. Then you can pull the machine out and tip it back against the wall to check the location.

What is model #?

If it's less than 5 years old, the warranty covers replacement of the top and lid due to rust. Check here:

http://shared.whirlpoolcorp.com/assets/pdfs/literature/Warranty%20Page%20-%203955869-W.pdf

They are all shown here

washing-machine-cycle-time-chart.pdf - Whirlpool

Whirlpool https://www.whirlpool.com > en-us > blog-posts PDF *Cycle times represent Whirlpool products and may vary by model. How much time do you have while your clothes are washing? Check our chart for an estimate. 1 page ..

Not easily unless they are just under the agitator. A full tear down, remove the case, remove the agitator, lift the drum. If you are lucky, you will find them part way through.

It sounds like the Start/Run Capacitor has failed on the motor control board. The motor buzzes when they fail. The capacitor gives the motor a jolt of power to get it turning.

ck this out.... https://paradiseapplianceservice.com/washer-repair/how-to-reset-your-whirlpool-washing-machine/

Hi

If the washer won't fill you'll need to check for the water inlet hose, the water inlet valve and the pressure/water level switch assembly. Inspect the inlet hose coming to the washer for any blockages. If the hose is not clogged then check the water inlet valve for any clogs, if the water will not even fill for few seconds then certainly the water inlet valve is bad and should be replaced. You can also use a multimeter to check continuity on inlet valve. If you don't get any value on the multimeter then you'll need to replace the water inlet valve assembly. However, if the valve is fine then the pressure/water level switch assembly should be replaced. Hope this helps... Please post back if you need more information.

Daniel

Question moved from Cars and Trucks. All questions need full 'make model (what it is)'. That will put you into the right category. I moved you to Whirlpool. The Door lock has failed. https://www.google.com/search?q=Washer+F22+Error ..

Hello Kim, we're sorry to hear about your Washer. We recommend disconnecting power from the breaker for at least a minute and then turning the breaker back on to do a master reset on the Washer. If you are in need of help after trying the reset, can you please email us your address, phone number, the model and serial number, the website you were contacted on, Fixya, your review ID, and date of purchase to [email protected]?

Knowed as F8 E1 error code...
This code indicates there maybe a problem with the water supply to the washer. Turn on the water. Check the household faucets to see if the hot and cold water faucets are turned on. Completely open both faucets for proper fill.

NOTE: Both hot and cold water must be connected to the washer and turned on; the washer will not properly operate with only one incoming source of water.

Turn off the water and remove inlet hoses from the inlet valves in the back of the washer. Inside the inlet valves are screens. Remove any accumulated film or particles from the screens. Reinstall hoses, turn on water, and check for leaks. See the Installation Instructions for details; you can find them by entering your model number in the search tool below.



Is the water pressure less than 10 psi? If the water pressure is too low, the washer may not properly operate. To find out your exact pounds-per-square-inch (psi) value, contact your local water utility company.

Are you using HE High Efficiency detergent? Use only HE High Efficiency detergent. Using non-HE detergent, or more than the manufacturer's recommended amount of detergent, can cause excessive suds. The excess suds can prevent the washer from detecting the incoming water.

Concentrated detergents labeled 2x and higher will require a small amount of detergent based on load size. Always follow the manufacturer's recommendations.

To remove the error display, press Power once. Then press Power again to restart the washer. If pressing Power does not work:
Unplug the washer or disconnect the power for one minute.
Plug in the washer or reconnect the power.
Re-select the cycle and press Start.

NOTES:
* On some washers, when the washer is started for the first time after this error code, it will begin to drain. You will not be able to pause or cancel the cycle for about 8 minutes while it drains. This is normal.
* If the error remains on the display, and all of the other conditions above have been checked, call for service.

Hope this helps. Your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day.

If you need a control knob assembly for your Whirlpool LSQ9564MQ0 washing machine, there are several options you can explore:

1. Contact Whirlpool Customer Service: You can reach out to Whirlpool customer service to see if they have the part available for purchase. You can call them at 1-800-253-1301 or visit their website to chat with a representative.
2. Check Online Retailers: There are several online retailers that specialize in appliance parts, such as PartSelect, RepairClinic, and AppliancePartsPros. You can search for the control knob assembly for your specific model and order it online.
3. Check Local Appliance Repair Shops: You can also check with local appliance repair shops in your area to see if they have the part or can order it for you.

When replacing the control knob assembly, be sure to follow the manufacturer's instructions and turn off power to the appliance before beginning any repairs.

The error code "F" followed by a number and a dot on a Whirlpool Cabrio washing machine indicates a fault has been detected in the machine's control board. Without the specific number that follows the "F," it is difficult to determine the exact issue. You can try unplugging the machine for a few minutes and then plugging it back in to see if the error code clears. If the code persists, you may need to consult the user manual or contact Whirlpool customer service for further assistance.

Mine does exactly all of those things you mentioned. I can't afford a new washer or even a new washer if they gave me a credit I also get white spots on my dark clothes and I am using very little detergent.

To replace the spring on your Whirlpool washer SM8525492-B, you may need to remove the upper control panel. Here are some steps you can follow to do this:
1. Unplug the washer from the electrical outlet to ensure your safety.
2. Remove the end caps on each side of the control panel. These end caps are located at the top of the washer and can be removed by pulling them off.
3. Once the end caps are removed, use a screwdriver to remove the screws that hold the control panel in place. There should be two screws, one on each side of the control panel.
4. Once the screws are removed, slide the control panel forward to release it from the clips that hold it in place.
5. Tilt the control panel back and rest it against the wall. Be careful not to damage any of the wires or connections that are attached to the control panel.
6. You should now have access to the springs on the washer. Replace the spring as necessary, and then reattach the control panel by reversing the steps above.

If you are still having trouble removing the control panel, it may be helpful to consult the washer's manual or contact a professional for assistance.