Whirlpool Freezers - Answered Questions & Fixed Issues

Question edited for clarity. This might be close enough? Contact details on Page 1 and 2. https://www.manualslib.com/manual/191418/Whirlpool-Upright-Freezer.html https://www.google.com/search?q=Whirlpool+SVF15NRHW01+manual ..

If your Whirlpool upright freezer is working fine but an intermittent alarm is sounding that is different from the high temperature alarm, it could indicate an issue with the door or the door switch. The alarm is designed to alert you if the door has been left open for an extended period or if the door switch is malfunctioning. Check the door seal to ensure it is tight and the door is closing properly. You can also try cleaning the door switch to see if that resolves the issue. If the problem persists, it may be necessary to contact a professional for further assistance.

??????? ?????? ?? ???? ??????? ???? ???? ?? ???? ?? ???? ???????? ????????? ???????? ???????? ? ???????? ??? ?? ???.

I have the same problem. Could be 2 things. 1) The top lid may not be all the way down sealing. I had to out some weights on top to make it seal better. 2) The lid seal could be cracked, partial missing or just not sealing. Good luck trying to find a new seal. I'm still looking.

THIS question is your only question here on Fixya dot com! https://www.fixya.com/users/gregg-j-ajamian You just need a good search query to find stuff like this. Cut out all the extraneous words and use the bare bones. Videos in the link https://www.google.com/search?q=whirlpool+upright+freezer+EV250NXTQ03+remove+the+drain+grommet ..

Try removing the strap holding the drain hose underneath that drains into the pan. Otherwise it acts like a p-trap and holds water that then insulates the upper part of the tube. Condensate water eventually freezes high up in the tube and backs up everything pushing the condensate water into the bottom of the freezer where it freezes into sheets. Leaving the drain hose down keeps air in the tube all the way back up into the freezer area. This seems to keep the condensate water flowing freely into the bottom pan. The air in the open condensate tube does not seem to have an ill affects. Also, you can add some stranded bare copper wire around the heating element just above the drain tube inlet and then push the tail off the copper wire down into the drain tube hole. This helps keep any water in liquid form flowing down the drain pipe.

There shouldn't be any 'jingly tone' at the end of every compressor cycle. You could be hearing something else making a sound after the compressor stops.

The larger one

The door switch or door module is defective. or the door is not fully closed

http://www.fixya.com/tags/freezer_green_light_flashing/browse/whirlpool

The defrost water from the melted frost (ice) collects in the bottom of the freezer. If there is no plugged up drain, then you must remove the water manually with a sponge and bucket after a defrost cycle.

If it’s in floor if freezer, you have a clogged defrost drain. If it’s on inside back freezer wall, it’s a defrost problem

did you get it fixed?

That appears to be a temperature alarm with that model. Whirlpool EVL201NXRQ04 Use Care Manual Manual has telephone numbers for support.

The solenoids that operate the ice maker and the water dispenser in the door may be getting water internally. I would put a pressure regulator on the line of the pressure exceeds 30 PSI.

https://www.repairclinic.com/RepairHelp/Refrigerator-Repair-Help I’m happy to assist further over the phone at https://www.6ya.com/expert/david_dc2f9e0a44104720

All cooling/heating appliances must have a functioning device to control the rise and fall of temperature. I’m happy to assist further over the phone at https://www.6ya.com/expert/david_dc2f9e0a44104720

The freezer is where the cold air is generated. It knows that is not logical to turn off the fresh food side so it determines that it needs the cold from the freezer side, so it over rides the error and will attempt to start. Turn your freezer on to a mid way setting ans give it a few hours to comply. I’m happy to assist further over the phone at https://www.6ya.com/expert/david_dc2f9e0a44104720

Locate a factory authorized technician and have them service it under the warranty, if it has one. The manufacturer should have a complete list of companies that do independent techs. I used to be a tech. for 35 different companies, so they are out there. I’m happy to assist further over the phone at https://www.6ya.com/expert/david_dc2f9e0a44104720

https://www.repairclinic.com/RepairHelp/Freezer-Repair-Help This site has diagrams, wiring, schematics, etc. I’m happy to assist further over the phone at https://www.6ya.com/expert/david_dc2f9e0a44104720