Staples Recent Questions, Troubleshooting Help & Support

Questions like this need a model number. See if this helps

How to Load Staples in a Boston 135 Stapler

Weekand https://www.weekand.com > ... > Furnishings Jul 21, 2017 - Insert heavy-duty staples into the staple holder, pushing back on the spring that feeds the staples forward until the staples are loaded. Gently ... ..

https://www.mybinding.com/media/manuals/swingline-assorted-breeze-automatic-staplers-42131-manual.pdf https://www.youtube.com/watch?app=desktop&v=QkkQH8vY9zM

The back of the Screen at the bottom there are two small screws just move the back cover and you would find to replace the battery. Posted on Aug 03, 2022

You have to shove your finger down to the bottom where there are two latches you have to pop out. They are on the bottom, closer to the front of the cupcake. good luck.

Usually a jammed or bent staple in the throat at the end.

Pull rear lever to open magazine and load staples. The Bostitch P3 uses SP19 1/4? staples.

Bostitch P3 Stapler - Agricultural Supplies - MIDCO Global

Question edited for clarity and typos. Either mains voltage instability, or the internal switch has gotten a 'hair trigger'. Clean and lubricate. https://www.google.com/search?q=rapid+5080+electric+stapler+troubleshooting ..

Usually the plate will swivel 180 degrees to give an open staple for easy removal, or a closed staple for permanent fastening. Push up from underneath and turn it. https://www.google.com/search?q=Swingline+heavy+duty+stapler+manual ..

Question edited for a bit more clarity. It is a SPL S242D, not 2420. Question moved to a better category. Duplicate post deleted. Refresh page to see your question. Please don't type in all CAPS, it is considered SHOUTING and is harder to read. Take the bin out. Lay it on its back. Use a vacuum cleaner with the round brush attachment to vacuum out all the dust playing particular attention to the sensor in the upper section. Put the bin back in with it lying down and gently sit it back upright. It should work now.https://www.google.com/search?q=SPL+S242D+SHREDDER%2C+open+door+light

The new staples aren't in correctly of the last staple in the old magazine, is jammed that the end. You should try to never run completely out. WOW, a thousand bucks for an office stapler!! https://www.google.com/search?q=Swingline+270 ..

It is likely that you are having a mechanical problem with the stapler in this situation. Check to make sure the spring-loaded chute is open and not jammed in the closed position after making sure the stapler is empty of any staples. Try putting the stapler arm back into its resting position by applying pressure on it. If this doesn't work, you'll probably need to disassemble the stapler to find the problem and fix it.

logic says to try staples....

I am not sure what you mean by a LOCK OUT KEY but perhaps this link to the manufactures site might help. www.fellowes.com/us/en/support/Pages/faqs.aspx Fellowes Support FAQs

You can find a replacement from this eBay listing: https://ebay.us/9mUhmN

Please inquire at Staples with all info on the shredder as to whether a replacement key is available........or call tech support for Staples shredder.

Toll free telephone number on first page of the manual at the link below: https://www.manualslib.com/manual/770121/Staples-Spl-Txc122a.html Staples SPL TXC122A Operator Manual

If your battery is fully charged but your stapler is not shooting staples, there are a few potential causes for this problem:

• The stapler's mechanism may be jammed or stuck. Check the stapler's mechanism and clear any jams or debris that may be preventing it from functioning properly.
• The stapler's spring may be damaged or weakened. If the spring is not providing enough force to push the staples through, the stapler may not be able to shoot staples effectively.
• The stapler's nosepiece may be damaged or misaligned. Check the nosepiece and make sure it is not bent or out of position, as this can prevent the stapler from shooting staples correctly.
• The stapler's battery or other internal components may be faulty. If the problem persists, you may need to have the stapler serviced by a qualified technician.

If you are unsure how to check for and address these potential causes, you may want to consult the user manual for your stapler or contact the manufacturer for assistance.

Rapid classic 9: kan enkel vanuit de achterkant gevuld worden. grote nieten zitten strak en glijden daarom er niet makkelijk uit. Haal de veer eruit. (Achterkant) Schuif de klem op de voorkant naar voren. (Zet er een schroevendraaier tussen). Druk het mechanisme een beetje in om het frontplaatje te verwijderen. De hamer (plaatje achter de frontplaat dient de tekst:FR aan de voorkant te houden) Druk met een lange schroevendraaier de nieten die erin zitten naar achteren, en haal deze eruit. Zet de hamer en frontplaat weer op de plek, en schuif de klem terug. vul het apparaat met de nieten die u wilt gebruiken.

Dont know what you are saying. Basically turn it off and on if your stuck.

They do this when they get dirty. There is a sensor that tells when it is full, the sensor gets paper dust on it and wont work in forward. You need to clean it real well. If that does not help then the issue is something else like sensor failure.