Splendide Washing Machines - Recent Questions, Troubleshooting & Support

Probably the drum bearing has past its best by date. Time for a new machine.

Have you opened and checked the pre-chamber pump trap behind the lower front cover? It captures coins and other large items from damaging the pump.

The issue you are experiencing with your Splendide Comb-o-matic 5200 could be related to several possible causes. Here are a few things you can try:

1. Check the water inlet valve: Make sure the water inlet valve is working properly and is not clogged or damaged. A malfunctioning valve can cause the washer to stop during the wash cycle.
2. Clean the drain pump filter: A clogged drain pump filter can cause the washer to stop working during the wash cycle. Clean the filter to remove any debris that may be causing the issue.
3. Check the motor: A faulty motor can cause the washer to stop working properly. If you hear a humming noise but the drum is not spinning, it may be a motor issue.
4. Check the belt: If the belt is worn or broken, it can cause the drum to stop spinning. Check the belt to see if it needs to be replaced.

If none of these solutions work, it may be a more complex issue and you may need to contact a professional technician for further assistance.

Gently use a screwdriver to adjust the door hook on the unit body outward so that the latch arm on the door engages with it once again when closing.

Question edited for a bit more clarity, correct maker name spelling. Question moved to model category. Parts suppliers for this RV Washer Dryer. https://www.google.com/search?q=splendide+2000+model+wd802m+parts I found one place that advertised it but out of stock, and it is $189!! $108 for a Used one! https://rvappliances.visonerv.com/cgi-bin/md/M320259/s1.pl ....

I have exactly the same issue. The door normally locks, but doesn't do anything on wash.

No, I doubt it. https://www.google.com/search?q=Spendide+ARWXF129W+remove+timer ..

Omg...thats your steamer thingy...nice. that's new tech. If it's a factory install and you have potable water in your holding tank and / or are hooked to water pipe you are good to go with the latest tech in fabric care. Lucky gal

bad timer

Question edited for clarity. Question moved from Cars and Trucks. If Yellow Jackets have nested in it, rodents have probably chewed through the wiring. Help from Splendide Technical training Guides below.

Splendide 2000 Washer Dryer Combo WD 802 Vented ... - eBay

https://www.ebay.com > ... $450.00. Splendide WD802M S2000 Washer-Dryer Hose-drum to vent 036024 ... Splendide 2000 WD802 WD802M RV Washer/Dryer Spin Speed Unipolar Switch 116102965 ...

Splendide Combo Washer Dryer Technical Education Site

http://www.splendide.com > service > docs WD2000S, WDC6200CEE. Combos (1996-2002), Stackables (2006-Present). Repair Manual (1.9M) Models: WD802M, WDC1024M, WDC1025M, AW122 Repair Manual (919K)

• Combo Washer-Dryer Parts Breakdowns - Splendide

  http://www.splendide.com > service > Combo_Par... PDF Jul 7, 2008 - Splendide 2000 (WD802) ... WD2000S. Splendide 2002 / 2004 Models. Model/Serial No. Designators ... Soap dispenser panel WD2000S B4 50404.

JB weld

bad controller most likely

Check water inlet valve. It maybe stuck open.

try it and see what it does .

check filter lower right side behind bottom trim

Sounds like the belt that turns the drum has come off or broken.

I have a splendide 2000 / WD802 pre m with round power buttons. It came with a used RV I bought. Everything would work on it except the drum wouldn't spin at all. After some research and messing around with it I was able to fix it! You remove the back panel and in the bottom left corner there is a white control module chip board mounted in by two screws. Remove the two screws from the back for access to fix it. Now the top plug on pin 1 and 2 shoud have 2 white wires connected to pin 1 and one baby blue wire connected to pin 2. I jumped these 2 pins together with a small length of wire and now our machine spins and works great! Be sure to use at least 6 inches of wire at least as thick as the rest of the wires and make sure that it is well connected. I recommend you take the crimps off the blue and white wires and re crimp them with the jumper wire crimped as well or solder the connection. If you don't have a good connection with a long enough wire it will get hot and possibly catch fire so it is very important to do this correctly. I hope this helps someone!!