Sony Televison & Video - Page 5 - Recent Questions, Troubleshooting & Support


Sounds like main board fault. These blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices. http://electronicshelponline.blogspot.com/
Blinking codes details to many popular brand TVs are given. Surf the site with patience.

Sony KDL-52XBR9... | Answered on Nov 05, 2019


An out-of-focus picture is usually caused by poor regulation of the Hi-Voltage circuits. In these older Sonys' it can mean poor solder joints in the horizontal output stages. Check all solder joints on the flyback transformer and filter capacitors on the secondary low voltage side. A less common problem would be a short in the picture tube or arcing in the focus block. Any of these problems will require the services of a competent service technician. This old of a set should not be considered for repair, but replaced with a newer flat screen.

Sony Televison &... | Answered on Nov 05, 2019


ASK GOOGLE FOR REMOTE CODE LIST .

Sony Televison &... | Answered on Nov 02, 2019


Firmware Update is needed.

FUNCTION IMPROVEMENTImprovement of Disc Servo firmware to correct "DRV ADJ err" or "DI read err" error message appearance. COMPATIBILITY INFORMATION
1.) If this model is used in combination with PDW-U1 or PDW-U2 ,upgrade XDCAM drive software to v2.3.2 or V3.1.1 or higher respectively.
2.) Windows & Mac FAM Drivers must be upgraded to V2.3.0 or higher beforehand
3.) XDCAM BROWSER must be upgraded to V1.3 beforehand.
4.) CONTENT BROWSER must be upgraded to V1.1 or above beforehand
5.) If PDW-F800, PDW-HD1500 or PDW-F1600 is used in combination with this model, it must first be upgraded to V1.71 or higher.
6.) HDCA-702 used with this model must be upgraded to V1.10 or higher.

CAUTION ABOUT UPDATE PROCEDURE
1.) Execute "All File Save" to Memory Stick before starting the upgrade,after the upgrade please execute "Factory Preset" followed by "All File Load" from MS.
2.) Be sure to use external DC Power,Battery not recommended.
3.) Implement software update without disc inserted.
4.) Set VDR power save switch to STBY position.
5.) Disconnect all I-Link and Audio cables.
6.) If the Power is turned OFF during the process,restoration of the software package will not be possible, be careful.
7.) Follow the installation instructions in the Release Notes.
https://pro.sony/qf_CA/product-resources/software-firmware/1237492951598
https://pro.sony/s3/cms-static-content/operation-manual/3297517131.pdf

Sony Televison &... | Answered on Oct 21, 2019


open the rem.control and clean the keypads for bad contacts, oxide, corrosion, and dirty.
and try again.
if the problem persist, go to the repair shop TV for fix it.
God bless you

Sony Nsgmr1... | Answered on Oct 13, 2019


sony model kv-g21p2 power on 2secon off what poblam

Sony Televison &... | Answered on Oct 13, 2019


Lift maybe locked. You need to turn on lift settings using remote. Cannot be turned on using TV controls.
Hope this helps.

Sony TAV-L1 32... | Answered on Oct 11, 2019

Not finding what you are looking for?
Sony Logo

Family Lines

43,477 questions posted

Ask a Question

Usually answered in minutes!

Top Sony Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76204 Answers

Jerry Greenberg
Jerry Greenberg

Level 3 Expert

1691 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a Sony Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...