Sony Video Cameras - Page 8 - Recent Questions, Troubleshooting & Support

Hi,
Read the Forum :-
http://www.pechorin.com/m/2004/03/07/Sony_DSC_F707_error_e6110-210360-3.html
I love to see so many people Fixed the problem using the same method.
Let me know, if the problem persists.
Thanks for using ' Fixya ' and have a nice day!!

try this find the web site for the handicam find a download for your model that is compatible with win 10 and download it if you have win 10 and win 8 on the same pc hard drive then there could be a conflict in drivers for the cam as well

hi, this error code indicates that some thing out of order related with the lens of the cam, if the camera section is jammed or dust entered in may be the cause, open the lens unit clean it with air blower ball, then fix.

Now you can get your answer in below table. In this case you have to replace board VC-577E:62:10 Shift lens initializing failure.**** When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustmentitems.After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.Now you can get your answer.Kind regards.Rehan Zafar.

Hi ! No I think you need a new LCD sreen ! But I think a new Camera is more efficient and cheaper !

You can get a video grabber (google video grabbers) and connect the RCA cable to the camera and the grabber USB cable to your computer. Run the grabber software and play the tape so the grabber can record the video from the tape in the camera.

try removing the battery from the camcorder which resets the unit. If not try holding reset for 3 sec and it should work then all you need to do is set defaults date time ect

It could be a dodgy Charger, if it has a problem and not kicking out enough power, it will think that the battery has power equal to that of the charger, i.e. fully charged altho' it isnt, and cut off, making it appear to all be working. If its a mini USB type charger you could try a different one from something else they are all 5v, but some draw more current (mA).

The Sony Handycam CCD-FX530 manual is the same as that for the CCD-FX430. This manual is available at ManualsLib: https://www.manualslib.com/manual/525601/Sony-Ccd-Fx430.html#product-CCD-FX530 . You can download the manual after clicking the Download button near the top left of the page. You will need to prove that you are a human to access the PDF. I hope this helps. Cindy Wells

the camera is not hi def

Im not sure about your computer setup. Are you capturing via usb or have dedicated video capture device? Do you have sound when connected camera to tv. Does your video capturing device require to supply sound separate for example from camera headphone jack to video capture device?

lens inside camera may be struck, open take out camera free the lens control motor or replace it

no, it should be in same format

I had the same problem and found numerous solutions on the internet. The most common and apparently most successful was to remove the battery and give the camera a sharp whack. Didn't work for me. I tried to find a seperate CMOS battery to remove that but couldn't but your model may have one - try that. Then I found a thread at http://www.dvinfo.net/forum/sony-hvr-a1-hdr-hc-series/88013-moisture-condensation-2.html which suggested cleaning the moisture sensor on the left hand side at the very back of the tape transport mechanism. It is oblong shaped, has two solder points at its top and (in my case) a black square that should actually be a black circuit like pattern. Scroll through the aforementioned thread and you'll find photos to help you locate it. Using a cotton wool bud soaked in CD lens cleaning alcohol (you'll need a long one or small fingers :-) a couple of wipes was all that was needed to reveal the pattern. I re-inserted the cassete but still the same problem. With the camera turned on I then used a paper clip to depress the reset button (Flap open the LCD screen and you'll find it under the auto lock slider switch). The camera "re-booted" and everything worked fine! I had to reset the date and time and all my settings preferences but no big drama. Hope that helps.

can camcoder picturer directly transfer in laptop without software download in which window

Reset the Camcorder.

Apparently not, said to be included already in Windows 10. https://esupport.sony.com/US/p/support-info.pl?info_id=543&mdl=DCRSR68 https://esupport.sony.com/US/p/support-info.pl?info_id=543&mdl=DCRSR68

Mains or battery

There is no file to open.

Well if you lost your sony handicam cd? well give the sony handcam model no. there are ways to make one in your system there.....go to google....type the model no togive the software google will guides you there will be your required software ...thereafter install .. it worksfirst follow the way how to install..belowhttps://www.youtube.com/watch?v=uJpT7SSarLY