Samsung Recent Questions, Troubleshooting Help & Support

You can get the unlock code through online..........give your IMEI number and get the unlock code for ur mobile.... i will suggest the website Unlock-Zone.com which is doing good service .....you can approach this website.
This site is nearly perfect and they were recommended highly in the cell phone forums. I used them to unlock my cell phone. contacted them and within 30 mins i had my unlock code and my phone was unlocked.
Hope this helps.

Hi g k,Have you tried restarting the print spooler from services?Start the Print Spooler service from the Services console

1. Click Start, click Run, type services.msc, and then click OK.
2. Right-click the Print Spooler service, and then click Stop.
3. Right-click the Print Spooler service, and then click Start.

Start the Print Spooler service at command prompt

1. Click Start, click Run, type cmd, and then click OK.
2. Type the following commands at the command prompt: net stop spooler net start spooler exit Note Press ENTER after each command line.

Hope this helps, and please rate:)Gary

First things to try: 1. Unplug the fridge and move it away from the wall. 2. Inspect the power cord for damage. Replace the power cord if it is damaged. 3. Plug the fridge back into the wall outlet. 4. Set the temperature control to the desired level. 5. Push the "Reset" button, located near the temperature control panel, to reset the temp control settings. The Reset button is usually red in color. 6. Move the fridge back to its original position.

Press the Menu button on your remote control. Navigate to Picture and select it. Scroll down to Expert Settings and select it. Scroll down to Auto Motion Plus Settings (Picture Clarity Settings) and select it. Change the setting to either Off or Custom.

If your Samsung Eco Bubble washer is filling with water till the top, it could be due to a faulty water inlet valve 1. You may need to replace the valve to get your appliance filling with water and working properly again . However, if you suspect that the sensor is not working, you can try the following steps : Check if the LED on the eco bubble wash button is on. Check if there is too little laundry in the washing machine. In case of heavily soiled laundry, bubbles may not be generated very well. Unplug the machine from the mains to ensure your safety. Locate the two screws on the back of the machine that hold the top cover in place, and unscrew them. Gently push the top cover back and remove it to expose the interior. Take out the detergent container. Identify and remove the screws that secure the front panel in place. If none of these steps help, please contact a local Samsung service center

Hi Andy, first off, please don't use caps when sending a message as it's harder to read and seems like your screaming. With that being said there are a few things in your message that I need to address, I pulled up a service manual on your TV and it doesn't have a tcon board, this set only has 3 boards, the power, main and wi-fi card, so not sure what boards you're calling the tcon boards. Next thing I don't understand is you said when you disconnect the power going to the main you have sound, that's not possible, if you unhook the power to the main you would never get sound so I assume you may have unhooked what's called the LVDS plug, that's the flat ribbon cable going from main to in this case to the panel boards. On Samsung sets if the connector is unhooked going to the main board the inverter that drives the backlights will come on and you will get backlights if they're working like they are in your case. You said if you hook it back up you get a fluctuation of a blue and black (no backlight) issue. What I believe you have going on is a short in either one of the COF (chip on film) IC's or another device on one of the panel boards is bad. What I want you to do is unhook one of the panel board connectors at a time and see if you get half a normal picture, you need to power the set off when you go from one ribbon connector to the next, I think you will find one of the boards is working and you get half a picture. Now for the not so good news, if the panel is bad the set isn't fixable, you can try searching "fixing a TV with a piece of tape" for an idea of how you may be able to get the set working again but it may not work totally correct.. I'm not going to describe this procedure as you will see how it works by the videos.

Install the printer/scanner software and use the menu system.

Well, it could be any of about 25 components that are bad, start by testing bridge rectifiers, if they look good test the main power mosfet, of that looks good look for a shorted component on the cold side of the power supply, Unless you have some form of degree in electrical engineering this may be a bit over your head.

No such option given in the Owner's Manual Samsung MW1080STA Owner's Manual download pdf (manymanuals.com)

Your best option is to get a technician to look at it and quote for a repair. A squeaky drum could be anything from the dryer not positioned level, a worn drive belt slipping, a worn out drum bearing or worn motor.

Question edited to add the further information. Has to be in the manual? Did you pull the mains plug overnight? That panel is called OSD (on screen display) and can be set to stay on for up to 200 seconds. Page 39 refers, and you can also reset it to factory defaults. https://downloadcenter.samsung.com/content/UM/200803/20080329132905671_BN59-00716A-Eng.pdf .

See Before contacting to a service center on page 83 of user manual ES28_English_V3.0 (samsung.com)

Type "Samsung A03 repair" on YouTube. Best of luck

According to a post on applianceblog.com, this issue could be caused by a blocked vent or vent hose, which can trigger the HE error. You can start by checking if the vent and vent hose are not blocked. If that's not the issue, you can try measuring the voltage across RY5, RY6, and RY7 on the main power board during a normal dry cycle. If there is no voltage, you may need to replace the control panel . If you're looking for more information on troubleshooting your Samsung dryer, appliancepartspros.com has a comprehensive guide that lists common symptoms and their causes for your model .

Question edited for a lot more clarity. Please proof read before Posting.. Question moved from Cellphones category. 40,000 to choose from RD is air damper iced up fault. The damper in the freezer spins around to close/open the air from the freezer to the fridge. It ices up from time to time, or the damper motor, or sensor that reads it's position fails. Apr 27, 2010

Hi. My samsung RL39WBMS fridge/freezer shows rd in the ...

If you can spell it, you can Google it! Lots more in the link. 'make model (what it is)' in all questions please. https://www.google.com/search?q=Samsung+refrigerator+RD+code ..

The battery has probably swollen, they do when left flat for a long period of time. Brute force is all you can use and hope you don't destroy the fixings.

Visit following website and run printer diagnostic. It may help you Samsung ML-2165 Laser Printer series - Troubleshooting ' HP® Support

Since you had a garment get caught in the door, check the hinges and the door latch and striker. Something could be damaged, bent, loose or deformed. You may be able straighten the part or replace the specific part to get the door to close properly. A problem with the door switch or the wiring is also possible. However, I wouldn't check that the switch is not providing the locked signal to the control board until the door closes with the correct alignment of the latch. If you do need to check the wiring, see https://fleetappliance.com/dryer-repair/how-to-fix-samsung-dryer-error-code-de/ for accessing the lock mechanism. I hope this helps. For further information, including a check for a parts list, please add a comment with the model number of your dryer. Cindy Wells

It sounds like you have an issue with the Anynet+ (HDMI-CEC) function. When the home theater system is connected to a compatible TV by an HDMI cable, you can sync the operations when this is enabled on both the TV and the home theater system. You need to be turn the feature off on one or both devices. If you have another HDMI port on the TV, you could move the HDMI cable to that port. (Most TVs only have one HDMI-CEC enabled port.) Note: this turns off the audio return channel option. If you only have the HDMI cable connected between the TV and the HT-EM53C, you will need to connect another cable. Depending on the TV, this could be an optical audio cable, analog RCA audio cable or headphone (3.5mm) to RCA audio cable. The manual for the Samsung HT-EM53C is available at ManualsLib here: https://www.manualslib.com/manual/355628/Samsung-Ht-Em53c.html . A summary of the Anynet+ feature is here: https://www.manualslib.com/manual/355628/Samsung-Ht-Em53c.html?page=29#manual . Accessing and navigating the Settings menu is discussed here: https://www.manualslib.com/manual/355628/Samsung-Ht-Em53c.html?page=25#manual . Press the Home button on the remote and go to the icon with the gear. I hope this helps. Cindy Wells