Samsung Office Equipment & Supplies - Page 8 - Recent Questions, Troubleshooting & Support
How to reset ML1640 printer
I dont really understand the question as when you insert a replacement toner it will inform the printer a new toner has been inserted, however if you are refering to Hardware reseting the page count please find a diagram here http://www.arbikas.com/forum/Attachments/ML1640_reset.pdf
How to fix the red light and not working on samsung ML-1866?
LED pattern Possible Problems and Solutions
Your system has some problems. If this problem occurs,
contact your service representative.
On Line/Error LED
lights red
• Paper jam occurs. To solve the problem, see "Clearing
Paper Jams" on page 5.6.
• The front cover is open. Close the front cover.
• Paper tray is empty. Load the paper in the Tray.
• The toner cartridge is out of toner. Remove the old toner
cartridge and install a new one. See "Installing the Toner
Cartridge" on page 2.4.
• You pressed the Cancel button while the printer is
receiving data.
• In Manual Feed mode, there is no paper in the manual
tray. Load paper into the manual tray.
• If the printer is receiving data, the On Line/Error LED
slowly blinks green.
• If the printer is printing the received data, the On Line/
Error LED blinks green fast.
Printer error A1-A4111 while sending to Samsung c1860FW Xpress printer
1. Before starting, turn off the power with the power switch next to the power cord then disconnect the power cord.
2. Remove any data cables since you will be spinning it all around.
3. On my printer (other models may vary) there are 5 screws that need to be removed first:
Facing the front, open the large lower front cover and remove the three screws on the front right
Turn to the back and open the back cover. Remove the two screws on the left. Notice any screws that are different and remember their position.
4. Slide the right side cover towards the back. It should come away easily. Set it aside.
Fuser unit failure #U1-2320
The Samsung printer error code u1-2320 is related to fuser that means the fuser unit fails. Need not to worry; this error can be encountered by many Samsung printer users. ... The Samsung printer error code u1-2320 is also the fuser error; this might be resolved just simply power off the printer.3
Transfer belt error, lever unlocking
Hello,
There is sensor inside the transfer belt, on the bottom side of the
transfer belt (pink side).You have to screw off 2 screws from the
plastic cover from the pink side of the transfer belt. When you screw
off plastic cover, you will see three wires which is going to sensor.
There is 1 screw which hold sensor; you have to screw off that and
gently pull out sensor. Sensor looks like letter U, and on the inner
side of the sensor there is two small holes on the opposite sides. You
have to clean that holes (blowing or with small brush). Clean it well.
After that, reassemble transfer belt, put it back, and turn on printer, that solve and fix the problem.
Take care.
Paper doesn't pick up
Check the feeder roller inside the printer for any foreign substance stuck to the roller, this may cause it not to grip properly. You can also try a few sheets at a time and make sure the paper tray is gripping the paper, but not too hard. If this fails, the roller may be out of place somewhat, try to reposition it. Let me know how you get on.
Replace/Install toner waste bin error
The toner box is probably full. The toner box is a clear box on the left side when you open the front cover. The box has the labels Y, M, C, and K on it. Pull it out using the tab at the bottom. find a place to empty it. You can do this by turning it upside down and gently tapping it. If the box is full some toner may be outside of the box causing the sensor to be blocked even after it is empty. You may want to clean the box, toner cartriges and inside the cavity with qtip, tissue paper (without lotion), or air.
Printer feeding multiple pages
After so much paper goes thru the rollers they pick up dust and dont stick. Some models you can unplug and then use a q tip soaked in alcohol to clean the roller. Others require you to take them apart to clean. If you have to take it in to get fixed then check out the new ones from a computer store. Sometimes its cheaper to get a new printer than go get yours repaired or cleaned. If you do decide to have it done look really close when they get done and ensure the rollers were cleaned with alcohol. Otherwise they mihgt still have a oil coating on then and that causes them to slip also, especially on photo paper. They will argue in some places that the alcohol will dry out the rubber and it will age and crack. Altho this is true I have yet to see a dry, aged or cracked pickup roller, even 15 years in the business. I think thats because it takes longer to age and crack a rubber roller than it does to just wear out the machine. Jonathon
Samsung scx-4825fm errer out-bin
hi
find link for samsung printer problems
http://www.samsungsetup.com/ts/manual/Samsung%20M288x%20Series/English/manual/CEGEGGFB.htm
Scx-4623f error not compatible toner
- Remove your new cartridge and replace it with the old one. Leave your printer and go and do something else for 10 minutes.
- Replace the old cartridge with the new one again. These two steps alone often resolve the issue, so see if your printer now recognises your new cartridges. However, if you're still having trouble...
- Remove the new cartridge. Make sure you place it in a clean and safe place where the cartridge or the surface won't be damaged.
- Turn the printer off using its power button
- Unplug your printer at the wall. It's important to do both steps 4 and 5 separately, as some printers can remain in sleep mode if you've only switched off the power button on the printer control panel. Leave your printer like this for about 10 minutes or so.
- Plug your printer back in at the wall (but don't press the power button just yet)
- Insert your new cartridge
- Press the power button on your printer
How to remove error samsung scx-3405f install toner cartridge
Try these steps:
1. Press MENU # 1 9 3 4 in sequence rapidly. The LCD panel should now display TECH.
2. Press MENU, and then press ENTER. The LCD panel will display Tech Mode.
3. Press the left arrow (<) button once. The operator panel will display NEW CARTRIDGE.
4. Press ENTER. The operator panel will display [YES].
5. Press ENTER. The toner warning message should be gone.
6. To exit TECH MODE, press MENU # 1 9 3 4 in rapid succession, as if you were dialing a phone number. The operator panel should no longer display TECH.
Let me know if it doesn't work as there is another possible solution.
I own a ML-2525/XAA and
Per your user manual, here is a list of all the LED status':
Jam (
)
Orange
On
A paper jam has occurred. (See Clearing paper jams.)
Online/Error (
)
Off
Green
On
Blinking
-
When the LED slowly bilnks, the machine is receiving data from the computer.
-
When the LED rapidly blinks, the machine is printing data.
Red
On
-
The cover is opened. Close the cover.
-
There is no paper in the tray. Load paper in the tray.
-
The machine has stopped due to a major error.
-
Your system has some problems. If this problem occurs, contact your service representative.
-
A toner cartridge has almost reached its estimated cartridge life[a]. It is recommended to replace the toner cartridge. (SeeReplacing the toner cartridge.)
Blinking
-
A minor error has occurred and the machine is waiting for the error to be cleared. When the problem is cleared, the machine resumes.
-
Small amount of toner is left in the cartridge. The estimated cartridge life[a] of toner is close. Prepare a new cartridge for replacement. You may temporarily increase the printing quality by redistributing the toner. (See Redistributing toner.)
Not finding what you are looking for?
