Roper Recent Questions, Troubleshooting Help & Support

No, it should pump out and add fresh water, agitate, spin, add water again, agitate, and then pump out for final spin. Check the pump and filter area for obstructions. Having said that, the logic board should halt everything and error out if there is no pump out. Try disconnecting from the wall socket for 15 minutes, and then plug back in.

Check the feet, they must all be firmly planted with equal weight and level left to right and front to back. If your Roper washer shakes excessively during the spin cycle, this can be caused by your machine sitting on an uneven surface, worn-out rollers, or damaged feet. To solve this problem, you will need to level the floor where your washer is sitting or replace its wheels if there are any worn-out parts.

Why Does My Roper Washer Shake And How To Fix?

Suspension rod failure or possibly a rod is out of place if the machine was moved.


https://youtu.be/h6wXWmEoVJY?si=Ubs3TurRVjDoJTpT

If your Roper top loading washing machine is stuck on the first wash cycle, you're not alone! It's a common problem that can be caused by a few different things. First, check to make sure the lid is closed properly. If it is, then you may need to check the timer, the water level switch, or the motor. If you're not sure how to do this, it's best to call a professional. Trying to fix it yourself could end up costing you more in the long run. But don't worry, you'll be back to washing your clothes in no time! Just remember, when it comes to washing machines, it's better to be safe than sorry.

Question edited for clarity. It is here

Im looking for the electrical schematic for my dryer. Its a

JustAnswer https://www.justanswer.com > ... > Appliance Repair Oct 22, 2017 · 1 answer Its a roper model: rex5634kq1, type: d433-ele-2406028-fm54. ... OK attached is the wiring diagram for your dryer.

There are normally three devices controlling heat overload, but I don't see them in parts lists. Thermostat, high limit cut out and thermal fuse. The thermal fuse doesn't reset, it basically blows and cuts power. If it is the timer, they are over $200 so call for service so they take the risk on it being right. Then you get the warranty on parts and labour. https://www.google.com/search?q=Roper+RED4640YQ1+parts ..

There are a few potential causes for your Roper washer not spinning or draining:

1. Drive belt: If the drive belt is broken or slipping, it could prevent the tub from spinning. Check the belt for any signs of damage or wear, and make sure it is properly tensioned.
2. Lid switch: Even though you said the lid switch is ok, it's still worth checking it again as it is responsible for ensuring that the washer will not spin or drain unless the lid is closed.
3. Motor coupler: The motor coupler connects the motor to the transmission and can wear out over time. If it has failed, the washer won't spin or agitate. Check the coupler for any signs of wear or damage.
4. Drain pump: A clogged drain pump or pump motor failure can prevent the washer from draining. Check the pump and clean out any debris that may be blocking it.
5. Control board: The control board could also be a potential culprit, especially if the washer is not completing cycles correctly. Check the board for any signs of damage or malfunction.
6. Transmission: If none of the above solutions work, there may be an issue with the transmission. This will require a professional repair.

I hope this helps you diagnose and fix the issue with your Roper washer.

Most of these spin related problems are attributed to a lid switch malfunction. A washer that fills and doesn't do anything, or stops right after the wash cycle and then does not advance to the rinse cycle and drain is commonly caused by a lid switch. The lid switch is usually mounted under the washer top casing, on the right hand side on most top load models. It is activated by a plastic piece on the lid (called a "Lid Strike") through a small hole on the rim of the wash tub opening. In many cases the lid strike breaks off the lid, or the lid switch becomes loose and no longer makes contact. Inspect the lid to make sure the lid strike is still intact, and then inspect the mounting screws (adjacent to the small opening on the wash tub rim) and make sure they are snug. If you determine the switch to be defective, the following link explains how to replace one:

http://www.fixya.com/support/r385198-replacing_lid_switch

If the switch requires replacement, a new one can be purchased on line at searspartsdirect.com, pcappliancerepair.com, repairclinic.com, appliancepartspros.com. Just use your model number as your search criteria. All these sites offer competitive pricing, so shop all them for the best price.

Let me know if you have any questions. I hope this helps you.

There are a few things you can try if your Roper washer is not going through the full cycle because it is only filling with a small amount of water:

• Check the supply of water: Check to see that all of the water supply valves are open and that the hoses are free of kinks and obstructions. The washer may slowly fill due to low water pressure.
• Check the valve at the inlet: The washer may not properly fill due to a clogged or damaged inlet valve. The valve may need to be replaced in this scenario.
• Verify the pressure switch by: The pressure switch tells the control board to move the cycle forward by sensing the tub's water level. It's possible that the control board won't be notified to start the next cycle if the pressure switch is broken.
• Examine the control panel: The control board may be defective and need to be replaced if none of the aforementioned steps resolve the issue.

did you click the pause/run button? sometimes that will unlock the door. if not then i would unplug the machine ..

Question edited for typos. Sounds as if the switch was wired wrong. https://www.google.com/search?q=Roper+washer+model+RAS8445KQ0+replace+lid+switch ..

Hi, Please power cycle your washer (ie unplug power for 2 minutes before powering on again). Then, you can move your dial counterclockwise (or opposite the direction that you currently turn your cycle-setting dial) by 90 degrees. Then, attempt a full cycle again. This should help somewhat reset your cycle functions so that it works properly. Thank you.

possible loose or bad belt if ok possible cogs under agitator worn

Depending on age, possibly time for a new one. There are fixes in the link. https://www.google.com/search?q=Roper+top+loader+drum+has+dropped+4+inches ..

Humming is normally indicative of a failed Start/Run Capacitor, but the fact you get nothing from it, leads me to believe it is a control board issue as well. Due the cost, call for Service so that you get the correct diagnosis.

The Timer Is Bad..Mine Only Heats In Perma Press..This Is After Replacing solenoid Valves And Thermal Fuse, Which Was Good.

Sounds like a bad control board or timer depending on the model. Because of the cost, it is better to get a service call and have it properly diagnosed.

possible bad transmission see if turns with out belt on

Gearbox / Transmission issue. Call a service tech. It is a greasy messy job and needs special tools. It take about an hour and a quarter.