Quinny Buzz - Recent Questions, Troubleshooting & Support

It all depends on the length or the screw and the thread of the screw itself. Check out home depot or any hardware store. Bring the stroller with you if needed and find a screw that fits. It should be an easy fix.

I like a product called whizz mould and mildew remover have used this on many things before even on a mothercare pushchair hood but it was a waterproof hood so not as absorbent. Maybe do a spot test first somewhere inconspicuous.

In case of baby stroller you should expend good amount of money. But there are some good brand strollers also in affordable price. You will get every type of stroller like jogger, lightweight,double and so on at mid range price. Best Rated Strollers 2017 Top Models Reviewed

Be sure it is the gas ram and not the cast aluminium anvil which the gas ram pushes against. The symtoms are similar
This 'L' shaped casting snapped in half on our Quinny Buzz and I managed to repair it by taking the whole centre hinge apart, drilling out the pin which holds one half of the aluminium anvil in place and removing this striaght piece of the anvil.
To repair I first glued the two parts together with araldite then held them in the vice whilst drilling through both pieces to a depth of about an inch with a 4mm tapping size drill. Then seperate the two parts, tap the shank out 4mm and drill the right angled bit 4mm clearance. Reconnect the two parts using a 4mm steel screw and some 'locktight'. Replace the anvil in its slot and replace the holding pin securing with araldite.
Reassemble the whole shooting match and it works ( well ours did....and still does!)
This seems to be a common problem but I could not find any spares. Also the holding pin for the anvil is not made to come out hence having to drill it out. So I doubt if any spares are available anyway.
Not easy and you need a few engineering tools to do the job. But much cheaper than a new frame assembly.

Hi Maxi-Cosi don't produce the adapters for the Maxi-Cosi carseat to go on the Babideal chassis. These would be from Babideal, so we'd advise you to contact them for assistance.

Hi We'd recommend you contact iCandy as they're the manufacturer of the pushchair, or contact John Lewis as you purchased from them.

First remove the front wheel assembly from the pushchair by pressing in the two buttons on the sides and pulling it out.

Now look more closely at the assembly - on one side, just where it bends at an angle you will find a small hole, a couple of millimetres across. Take a small screwdriver or some other thin object and push it into the hole a little way, which presses a metal catch inwards, releasing the swivel assembly. While continuing to push this in pull the swivel assembly apart - grasp the wheels in one hand and the L-shaped plastic housing in the other and pull them apart.

Now clean all the surfaces with a piece of strong cloth.

When all the surfaces are very clean, take a can of TEFLON SPRAY and spray it onto all surfaces that rub against each other, before reassembling the wheel unit. Silicon grease is a cheaper alternative, but the teflon spray is supposed to be the best for lubricating all moving parts on the Buzz. Whatever you do, don't use WD40.

Hope this helps! Dan.

Hi LindsayNot something we can advise you to repair yourself. Chassis would need to come in for our engineers to provide inspection / repair. If it is a 2008 model or younger we can provide this service. Standard charge is 39.99GBP and this does include courier collection & delivery of the product. Contact the customer care team on 01284 413 141 Mon-Thur 8.30-6.30 / Fri 8.30-4.30 (Excluding Bank Holidays) to book it in.

Hi - Please contact Quinny customer care by visiting the International Website and using the Contact Us tab - Quinny urban strollers and buggies

Hi - Please visit the Quinny website and use the Contact Us tab for your enquiry to be sent to your local customer care team who will be able to assist. Quinny urban strollers and buggies

Hi - Please contact Quinny customer care team by using the Contact Us tab on the website for your enquiry to be sent to the customer care team able to assist you. Quinny urban strollers and buggies

Hi - Please can you contact the Quinny customer care team who can assist you by using the Contact Us tab on the international website Quinny urban strollers and buggies

Hi - Please can you visit the Quinny page and use the 'contact us' tab for your enquiry to be directed to the customer care team in your country who can help you. http://www.quinny.com/international

HiGo to www.quinny.com and select the country you're in - choose the "Contact Us" tab on the right side of the page and your enquiry will be sent to the relevant customer care team for your country who can best assist with sourcing replacement fabrics for your Quinny Dreami.

Hi either are as stable, if you have a car you would be better off getting the car seat to match buggy. Mothercare have an excellent range

Watch this: