Proscan Logo

Proscan Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 171 Products
  • 3K Answers

Check for the reset pin hole on your tablet. Get a paper clip and push it 'gently' in the hole and hold it for thirty seconds. This resets the tablet.
Youdon't want to push hard as there is just a tiny button in there that can get dislodged.

Proscan... | Answered on Jan 03, 2020

Open internal fuse or power supply failure

Proscan... | Answered on Dec 18, 2019

  • Failing power supply
  • Defective power switch

Proscan... | Answered on Dec 06, 2019

go into picture set up and change to right side up

Proscan... | Answered on Nov 29, 2019

There should be a rest set system button , you may have to use a small paper clip unfolded to fit into the area. But that should do it. Good luck

Proscan 7-Inch... | Answered on Nov 26, 2019

Proscan DVD Codes = 2118, 2144, 2205, 2319. Proscan VCR Codes = 3000. ON MOST REMOTES: 1. Turn on the TV. 2. Press and hold the TV and SEL buttons simultaneously for 3 seconds. The button will light. 3. With the button lit, point the remote at the TV and enter the TV's 3, 4, or 5 digit code.

Proscan... | Answered on Nov 05, 2019

if not internet able use DVD player that is wireless for Netflix and other internet apps

Proscan... | Answered on Nov 05, 2019

if voltage at cord possible bad power board

Proscan... | Answered on Nov 05, 2019

Most likely it's the power supply board that went out. (part of it still works is why you get the blue LED when you plug it in.)

If you decide to try to fix it yourself, BE CAREFUL! The power supply board has capacitors that can hold high voltages for many hours after the TV's been unplugged.The equivalent of sticking your finger in a light socket.

You'll need the part number off the power supply to get a replacement.

Proscan 42LA45H... | Answered on Nov 04, 2019

I have a proscan tv and i tried connecting a usb cable to the usb service port, and nothing has showed on the menu options and nothing on the source menu... Is the service port any use?

Proscan... | Answered on Sep 10, 2019

After turning off the power, disconnect everything from the power outlets or surge protector. Wait for several minutes while all residual power exits the system. Return all the devices to power and turn everything back on. Check the television to determine whether it works properly

Proscan... | Answered on Sep 07, 2019

You need to connect the coaxial cable from the antenna to the TV's coaxial RF (TV) connection. (Really old antennas may need a signal adapter - 300 Ohm to 75 Ohm.) Then make sure that the current video source (sometimes labeled Input) is set to TV. On the later Proscan PLED1526A, there is an Input button on both the TV and the remote to cycle through the list of video source options. Enter the menu of the TV (on screen display). Now you should be able to find a sub-menu for setting the channel information. Using the newer model above, you may have a Channel option. Use the left/right arrows to reach that. Then press the Enter to enter the sub-menu. Navigate to Signal Type with the up/down arrows and set this to Air for over the air channels. (Use the left/right arrows to select the signal type and press Enter.) I believe the HRC is for certain cable systems. Then try the Auto Channel Search.

Note: if the TV was manufactured before 2007, it may only have a NTSC tuner. In that case, you'll need a set-top OTA converter box (ATSC to NTSC) to get most channels. Only low-power stations are still broadcasting the NTSC signals. Depending on the model, you can connect this to the RF port of the TV or the AV (composite video) or the YPbPr (component video) source with the appropriate cables. Change the TV input as needed. Then scan for channels following the directions for the converter box.

I hope this helps.

Cindy Wells

Proscan... | Answered on Jul 22, 2019

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Proscan Experts

The Knight
The Knight

Level 3 Expert

76204 Answers


Level 3 Expert

5748 Answers

ray gallant

Level 3 Expert

66042 Answers

Are you a Proscan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides