Pro-Fit Exercise & Fitness - Page 8 - Recent Questions, Troubleshooting & Support
1750 commercial Norditrack treadmill stuck on Whoops error occurred.
The "Whoops" error on a NordicTrack treadmill usually indicates a software or connectivity issue. Here are a few steps you can try to troubleshoot the problem:
- Unplug the treadmill from the power source and wait for a few minutes before plugging it back in.
- Make sure the treadmill is connected to a stable and reliable Wi-Fi network. If the issue started when you tried to connect to the Internet, this could be the problem.
- If the issue persists, try resetting the treadmill's software by following these steps: a. Hold down the Stop button and the Speed Up button while inserting the safety key. b. Hold the buttons until the treadmill beeps twice. c. Release the buttons and wait for the treadmill to reset.
- If none of these steps work, contact NordicTrack customer support for further assistance.
It's also possible that the previous owner may have sold you a defective treadmill, so you may want to consider reaching out to them for a refund or replacement.
Pacemaster Pro Elite Motor Controller 9501001 Rev J question
It is likely that the relay responsible for the incline down function is the one located at the lower right corner of the board. You may also want to check the power supply as well as the wiring of the solenoid coils connected to the board to ensure that they are working properly. Additionally, you should also check the motor controller board itself and make sure all of the connections are secure.
Discovery 415 error 11 will run for 11 seconds only
Error 11 on the Discovery 415 treadmill indicates an issue with the speed sensor. This sensor is responsible for detecting the speed of the belt and communicating it to the machine's computer. When the sensor fails or becomes dirty, the machine may shut down or display an error message.
To troubleshoot this issue, first, ensure that the machine is properly plugged in and that the safety key is securely in place. If these components are functioning correctly, check the sensor for any signs of damage or debris. Clean the sensor with a dry cloth, and check the wiring to ensure that it is properly connected.
If cleaning the sensor and checking the wiring does not resolve the issue, you may need to replace the speed sensor. Contact the manufacturer or a qualified repair technician for assistance with replacing the sensor.
MY WEIDER XP 600 WILL NOT ADJUST THE WEIGHT WLM
If you are having trouble adjusting the weight on your Weider XP 600, try the following steps:
- Make sure the weight stack is empty.
- Locate the weight selector pin and remove it.
- Check the guide rods and make sure they are clean and free of debris.
- Add the desired weight plates to the stack.
- Reinsert the weight selector pin into the weight stack, making sure it is fully seated in the appropriate slot.
- Attempt to lift the weight stack slightly to ensure that the pin is holding the selected weight.
- Repeat the process if necessary, making sure to choose the appropriate weight.
If the above steps do not solve the issue, there may be an issue with the weight selector mechanism or other internal components of the machine. In this case, it is recommended to contact Weider customer service or a certified repair technician for further assistance.
My edge 491 recumbent bike does not monitor speed or distance just says 0
There could be several reasons why your Edge 491 recumbent bike is not monitoring speed or distance and is only displaying 0. Here are a few troubleshooting steps you can try:
- Check the sensor: Make sure the sensor on the bike is properly aligned and free of dirt and debris. The sensor is usually located near the flywheel or on the wheel hub.
- Check the wiring: Ensure that all the wiring between the sensor and the display console is properly connected and not damaged.
- Check the batteries: Make sure the batteries in the display console are fresh and properly installed. Low batteries can cause inaccurate readings or prevent the display from working altogether.
- Calibrate the bike: Some bikes require calibration to ensure accurate speed and distance readings. Consult the user manual for instructions on how to calibrate your specific bike model.
If none of these steps resolve the issue, there may be a problem with the sensor or display console. In that case, you may need to contact the manufacturer for further assistance or consider taking the bike to a repair technician.
Any suggestions on how to deflect the sweat from the 2 lever joints on my elliptical, they're rusting.
There are several ways to prevent sweat from rusting the two lever joints on your elliptical:
- Use a towel: Keep a towel handy while using your elliptical and wipe down the lever joints periodically to remove any sweat. This will help prevent sweat from accumulating and causing rust.
- Apply lubricant: Use a silicone-based lubricant to coat the lever joints. This will prevent rust from forming and keep the joints working smoothly. Make sure to wipe off any excess lubricant after application.
- Use a protective cover: If your elliptical came with a protective cover, use it to cover the lever joints. If not, you can purchase a cover or use a large towel to cover the joints.
- Keep the room well-ventilated: Proper ventilation can help reduce the amount of sweat that accumulates on the elliptical. If possible, open a window or turn on a fan while using the machine.
- Clean and maintain the elliptical regularly: Make sure to clean the elliptical regularly and tighten any loose bolts or screws. This will help prevent rust and ensure that the machine is functioning properly.
I m facing an issue to repair on technogym console
I'd be happy to help you with your software issue on your Technogym Unity3 EJ. Here are some general steps you can take to try to fix the issue:
- Restart the equipment: Start by powering off the Technogym Unity3 EJ and then turning it back on again. This simple step often resolves many software issues.
- Check for updates: Check if there are any available software updates for your Technogym Unity3 EJ. This can be done by checking the manufacturer's website or contacting their customer support.
- Check for connectivity: Ensure that the equipment is properly connected to the internet or network. This is important for software updates and other features that require an internet connection.
- Factory reset: If the issue persists, you may want to try performing a factory reset. This will erase all the data and settings on the equipment and restore it to its original state. Be sure to back up any important data before proceeding with a factory reset.
- Contact customer support: If none of the above steps work, it's best to contact Technogym customer support. They will be able to provide more detailed and specific guidance for your particular issue and equipment.
I hope these steps help you to resolve the software issue on your Technogym Unity3 EJ.
if u like to tip :
https://paypal.me/AymanZiyat and ty
Trimline T340 treadmill "skips" or jolts to a stop for half a second, then resumes when any weight is on it
It sounds like there may be a mechanical issue with your Trimline T340 treadmill. Here are a few potential causes and solutions to the problem you're experiencing:
- Belt tension: If the belt is too tight or too loose, it may cause the jolting or skipping you're experiencing. Try adjusting the belt tension following the manufacturer's instructions.
- Belt alignment: If the belt is not properly aligned, it may cause it to slip or jolt. Check that the belt is centered and properly aligned.
- Motor issues: If the motor is struggling to keep up with the weight on the treadmill, it may cause the jolting or skipping. Check the motor and make sure it's in good condition. If you're unsure, it may be best to have a professional take a look.
- Deck and rollers: Check the deck and rollers for wear and damage. If they are worn or damaged, they may be causing the jolting or skipping. Replace any damaged components.
- Lubrication: Check the treadmill's lubrication. If it's not properly lubricated, it may cause the belt to stick or slip. Follow the manufacturer's instructions for lubrication.
If you're unsure about any of these potential issues or how to resolve them, it may be best to have a professional take a look. Using a treadmill that's not working properly can be dangerous, so it's important to get it fixed as soon as possible.
Where can I find my treadmill speed sensor?
If it's not in the typical location, there are a few other places it could be, such as near the front roller or underneath the motor cover. You could also try doing a visual inspection of the machine to see if you can spot any wires or components that look like they may be connected to the speed sensor. If you're still having trouble, you could try reaching out to online forums or communities for treadmill enthusiasts to see if anyone else has had a similar issue and found a solution. I hope this helps!
My life fitness elliptical keeps paUsing every 30 seconds, how do i stop it
I had the same problem with my 91X, put in a fresh battery and checked the magnet on the large wheel but it still did the same thing, finally i called the manufacture and the guy said its most likely bad or dirty brushes in the alternator, I took a picture of the wires, disconnected them removed the brushes cleaned them with acetone, reassembled and bam! worked like a charm, hope this helps someone
Urevo treadmill - knocking noise
A knocking noise coming from the rear roller of a Urevo treadmill can be caused by several issues. The following are some troubleshooting steps you can try:
- Check for loose bolts: Make sure that all bolts and screws that hold the frame and the roller in place are tight and secure.
- Check the belt tension: Ensure that the belt is tight enough. If the belt is too loose, it can cause knocking and other noise issues.
- Check the rollers: Make sure the rollers are not worn or damaged, as they support the weight of the belt and can affect the alignment of the belt.
- Check the deck: Make sure the deck is not damaged or worn, as this can cause noise issues as well.
If the noise persists after trying these steps, it's best to stop using the machine and seek assistance from the manufacturer or a professional repair technician. Using a machine that is making a knocking noise could potentially be dangerous and lead to further damage.
When I turned on my pro form 540s treadmill using the magnetic key it turned on like normal,
The issue with your ProForm 540s treadmill is likely due to a problem with the speed control circuit. Here are a few steps you can try to resolve the issue:
- Check the speed sensor: The speed sensor on the treadmill can be damaged, causing the control board to shut down the machine. Check the wiring and connections to the sensor, and replace it if it's damaged.
- Check the wiring: If the wiring connecting the control board and motor is damaged, it can cause the control board to shut down the machine. Check the wiring and connections for any damage, and repair or replace as necessary.
- Check the control board: If the control board is damaged, it can cause the machine to shut down. You can try to reset the control board by unplugging the machine from the electrical outlet for a few minutes and then plugging it back in. If the issue persists, you may need to replace the control board.
If you're not comfortable with the above steps, it's best to contact a qualified repair technician for assistance.
Is an E8 error on Ancheer treadmill fixable?
Whether an E8 error on an Ancheer treadmill can be fixed depends on its underlying cause. Possible causes like a broken control board, loose wires, or a damaged motor can sometimes be resolved with proper repair or component replacement. It's best to seek assistance from the manufacturer or a professional repair technician for proper diagnosis and resolution.
E8 Error Code on my Murtisol treadmill after 10 minutes. Can this be fixed?
An 'overweight' situation, often stated in error. Try lubricating the belt. I found this;
What does E8 mean on a treadmill?
Overload Condition
Answer: I had an E8 error on my Ancheer treadmill last year. It means an overload condition. At the time I was at least 60 pounds under the stated weight limit.
..
Not finding what you are looking for?