Pioneer Televison & Video - Page 3 - Recent Questions, Troubleshooting & Support

Ms Darlene All televisions need remote controls and they are readily available for about $20. Without a remote you can only do the most basic changes. Google make model replacement remote There have been issues yesterday and today with wifi enabled televisions suddenly quitting. Try this Turn off the television. Remove the network cable. Reboot the router and wait 15 minutes. Turn on the television. Plug in the network cable. Set up WiFi, (but you may need a remote). EVERYONE needs a remote!

These blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices. http://electro-medical.blogspot.com/ Blinking codes details of many popular brand TVs are given. Surf the site with patience.

I don't work on Pioneer TV's but the flash code could be helpful if you can find what 8 flashes stands for.

Mine did the same a couple of days ago, I have taken in for repair, will get back once with details soon.

PERHAPS AT A DEALER

This happens all the time to me. I need to use a paperclip every time. So annoying.

me . china

Set-up (Programming) procedure is too much to type in here, and is not practical and it will differ brand-to-brand remote controls. If you wish to get more; check the sites linked here. It has set-up code list & set-up procedure to many popular brand remote controls. One among it has general set-up codes to check with TVs and other devices are given, in the order of the 'device's brand name list' in alphabetical order. Pull up older posts. Search the sites by type in the brand name to your device in its search box at the right column of the display window. It will help you to find the document easily. https://homenol.blogspot.com/ https://elektrotricks.blogspot.com/ https://remotesearch.blogspot.com/ https://electrohelponline.blogspot.com/

Power up and press open button as soon as it starts to spin, some dvds lock with read errors, some spit the disc out.. If the belt is worn open unit, remove tray and replace rubber belt, if you dont have one use a thick rubber band. if you cant access rubber belt, most dvd's have a slide underneath. use a small screwdriver and manually slide it open. Read errors are not always the laser...so dont go and waste money. If your dvd is not hq using dc brushless motors, remove loader, give the spindle and sled motor a good lube with wd40, spin the spindle moto up with 5-7 volts to clean the commutator. Carbon builds up and the motors dont spin at correct speed. Sled remove drive gear, usually pops out and burn it clean as above. I have had good results with above since 2004, repaired 1000's of dvd's over my 14 years as senior engineer for wholesale importer in cape town. Good luck 44ct357 CT SA

Try 166, 172 or 038

Good point :>) Connecting it to a computer, may show it as a volume, but that would be all. As I said, you have an issue that no one else has ever put into Google. That means it is very, very rare. Contact Pioneer direct. It will probably have to go to a Service Centre and be connected to dealer software. No updates https://www.pioneerelectronics.com/PUSA/Support/Downloads

• Frequently Asked Questions
• Contact Us
• Find a Service Center
• Custom Install
• Factory Repair
• Software Updates

If it is 'PRICT', you are the only one to have that error in the universe! Details on resetting are in the manual. Download it, CTRL+F, type 'reset', press enter. https://www.manualslib.com/manual/130334/Pioneer-Htz170dvd.html#product-XV-DV170

Google make model remote replacement No 'control universal!

bad control board

Make sure that the blue-ray player (HDMI Out) is connected to your TV (HDMI In) with an HDMI cable. Set the TV to the input for the player. When not viewing any content, press the Home (Menu) button. Choose the Setup icon on the screen, using the left/right buttons on the remote. Press Enter. Use the Up/Down arrows to highlight Others and press the right arrow button. Use the Up/Down arrows to highlight ARC and press Enter. Use the Up/Down arrows to highlight Yes and press Enter to confirm and save the setting. See page 38 of the manual for the XV-BD717W for the information about the Others sub-menu (including ARC). Make sure that ARC is available on the TV and is enabled if needed. The manual is available here: http://docs.pioneer.eu/Manuals/BCS_313_AFN75473217_LG_manual/ . I hope this helps. Cindy Wells

Manual. Page 20 Button 5 = MUTE https://www.manualslib.com/manual/983762/Pioneer-Xv-Htd520.html?page=20&term=mute&selected=1#manual ..

Sounds like power supply issue. If you are UK based I have a complete set of Plasma Panels that are unused from my time as a Pioneer Service Department, now retired. jon@jonsnell dot co dot uk

1. Open fuse 2. Power supply failure

I rearranged furniture in my living room, picking up my pro-151fd elite, plugged it in to have no power, tried everything I could think of including an overnight reset. Thought of what could be the common denominator with most of the issues that people have, it's that they picked it up, felt under the front left and turned the tv on. The switch is not labeled, is part of a sqaure protrusion at the very bottom of the tv, 1" to the right of the "Pioneer" label, hope this helps someone who just has a dead tv without the blue flashing lights.

yes