NRS Health & Beauty - Answered Questions & Fixed Issues

Question edited for clarity, Hoveround not Hooveround. Added '(what it is)'. All question need full 'make model (what it is)' please. Question moved from 'Rode Microphones'. Bad connection on your motor. Bad connection on one of your batteries. Or a motor, or the controller / board has failed. all can be tested. https://www.google.com/search?q=hoveround+goes+in+circles ..

Question edited for full 'make model (what it is)'. Question moved from Cars and Trucks. Yes, it sounds like the gearbox needs service. Perhaps some new bearings or just lubrication.

sorry to tell u this but with a new controller and joystick u will need a tech with a programmer to redo the joystick and det up controller,so contact a dealer for help

If you plug the charger into the wall, turn on the power switch and the light comes on, the charger should be working properly. Here is a way to test it-
Attach the charger that came with the power chair to the power chair controller firmly and turn the power chair on, while the charger is running. What should happen:the lights on the controller will scroll back and forth. If this does NOT happen and you can confirm the charger is turned on, the charger handle is fully seated inside the controller receptacle and the wall outlet has power, then the charger may have a problem and needs to be replaced.

If the charger is OK, then there may be a problem with the batteries. Here are some sypmtoms:
1-You connect the charger but the light on the charger never goes red, it just stays green.
2-You connect the charger but the light goes from red to green VERY fast.
3-The charger light goes from red to green but when you disconnect the charger and press the power button on the controller, you only have one flashing red light, or the batteries drain within just a few minutes of use.
4-The power chair has been stored or sitting idle for several months.
5- The power chair has been connected to the charger 24-7 for several months.
Any of the above examples indicates that the batteries are oxidized or damaged and will most likely need to be replaced. The MPV5 takes two, U1 12 volt 33 amp batteries which can be purchased at any battery warehouse store like Interstate Batteries or Batteries Plus.
Good luck!

When changing a wheel one must remember to reinstall the shaft key, or the wheel will not be secured to the shaft. The shaft of the motor is turning but wheel is not. I’m happy to assist further over the phone at https://www.6ya.com/expert/bill_bcbb89783b08c489

Unfortunately your batteries are either disconnected or dead, below charging threshold of 16v. Time to check the connections and/or replace the batteries. I’m happy to assist further over the phone at https://www.6ya.com/expert/bill_bcbb89783b08c489

Most of the time it may be the batteries at fault. One more thing to try is charging the chair with the Joystick on all night 10-14 hours uninterrupted charging. Your chair may suffer from current roll back. There is a circuit in your system that has to be reset by the long charge cycle to reset it. I did not make this up. it occurs when the motors over heat or have a a large current draw. the chair will operate normally for ten maybe even twenty mins. then suddenly drop down to 2 flashing red lights. I’m happy to assist further over the phone at https://www.6ya.com/expert/bill_bcbb89783b08c489

if it is not working check freewheel levers I’m happy to assist further over the phone at https://www.6ya.com/expert/bill_bcbb89783b08c489

Time to replace the battery with a new one.

This part is for an Invacare power wheelchair with TRSS. This is a tilt and or recline single switch for actuator control. A search on the Invacare website shows an active part number and no price. A search of e_bay shows pricing between 50 and 150 dollars. This switch is easy to replace. plug the black "Lego " block into the power source, the 2 pin Anderson plug into the actuator and the Molex into the limit switch. You may need to switch the plug polarity of the 2 pin output to the actuator to get it to go in the right direction. The part was used on MkIV and MkV and some MKVI systems and should be readily available on line. Hope this helps.

It sounds like you may have bad bearings in the caster wheels; replace them and see if that solves the problem.

There is no reset button.

The pressure is 50 PSI, but 45 PSI worked better for me.

It is possible that the new batteries are bad. This happened to me once. The charger though is probably the culprit for your problems. Have the charger tested first, or ask a scooter or power wheelchair store test or charge your batteries.

There is a bolt and nut to tighten. Put a 1/2 nut drive tool between the front tire's 3 o'clock position and the tire fender. Tighten to add back the resistance.

Is the plug one way direction? more details please, it seems the plug is connected in the wrong position

Plug it in and charge the battery.

You are much better off just buying the flat free drive tires with the wheel attached for @ 55 each. With that being said, the wheel will separate it takes a lot of elbow grease, a large flat head screwdriver and patience. Be very careful not to tear and/or stretch the tire bead and resist the temptation to spray lubrication of any sort to separate it. Again, call Hoveround or look on ebay and order two with the wheels.... you will be glad you did..

The serial number typically does not have any involvement with Medicare but is used by manufacturers and DME providers to track the chairs. The true definition of what is a group 2 power chair would take a long time to explain but single option Group 2 chairs are coded: K0835-K0840 for single power option and K0841-K0843 for multiple power option. The specific code depends on the specific chair the person meets medical coverage criteria for. The Hoveround MPV5 you have pictured would typically be K0836 - Power wheelchair, group 2 standard, single power option, captains chair, patient weight capacity up to and including 300 pounds