Northstar Garden - Popular Questions, Answers, Tips & Manuals

Sounds like the trigger is not closing, best to strip it down and check operation. Probably siezed in the open position.

Cannot. Ensure u have a 3000psi wand.

PDF]Owner's Manual - Northern Tool + Equipment

https://www.northerntool.com/.../1577544.p... Northern Tool + EquipmentCall NorthStar Product Support 1-800-270-0810 .... -During transportation take precautions to make sure pressure washer will not tip ..... A- Low oil shutdown.

If it connect to the outlet pipe/lance then it operates on SUCTION similar to blowing across the top of a beer bottle to make a noise. If thats the case it is a matter of blockage and ventilation of the soap bottle to allow air to enter as the soap is sucked out by the water flow.

Water inlet filter lime or dirt , 2 nozzle dirt 3 floss with o-rings valves 1 valve has dirt or broken o-ring between 1 of the valves 4 pressure control valve was not screwed. the nozzle (if it is a dirtkiller) is is broken mostly porcelain.

I think you mean an UN Loader this is a valve that redirects (bypasses) the pressureized water back into the intake when you release the trigger When it is not working the machine continues to build pressure and will bog down hope this helps the ed

If it really bogs down to where the engine is struggling....it's the carburetor. It's not allowing the engine the fuel/air ratio it needs for peak performance.

If it is a twist coupler which won't turn, i use a pipe wrench or channel locks. If it's a quick coupler socket and the sleeve won't pull back, the quick coupler plug is bad. If you can't get them apart, both should be replacedTodd Lehkereplaced.

thats exaclty what a unloader valve does it unloads the pump when the trigger on wand is not depressed , it should however reseat and close off when trigger is pressed giving full presure to wand tip

THIS SOUND LIKE YOU NEED A NEW SEAL

There will either be a drain plug in the side or on bottom of engine. you can also tip the engine and pour it out from the fill port.

You can get ground tested for a water supply. We wanted to deepen our well for our house. We hired a drilling company to test the ground to see if water was present. Elisa Jed ' http://www.foulkbros.com

most lawn mower shops can handle any repair on engine part of machine its the same engine thats on lawn mower , the pump well thats a bit more tricky , what i have done is remove it from engine and drain fluids and send it back to mfg for repair they send it back you install it back and put fluids back inside , whholla it works !!!

Ensure all your additional rough in plumbing is capped, and toilets or sinks that are not used for long periods of time , sometimes p traps may dry up allowing sewer gasses to enter the home so use them once in a while or fill with water once in a while ,same with floor drains. If that isn't it check that you have them installed.

Sounds like the float in the carb is stuck. Take the bowl off, and check to see that the float is moving freely. Also check to see that the needle valve seat is clean - use a qtip or small wooden dowel to clean the seat.

NGK bp4es

Usually the rewind spring or spring anchor points are broken. The starter must be disassembled and the parts inspected. Remember the spring is under tension! [There are many different types of starters, and a manual is a good idea if you are not familiar with them.] If the starter is hard to pull, remove the starter and then try it. If the starter is ok off the engine, check the engine itself for a seized or oil-locked cylinder. Remove the plug and pull rope the motor, if it will now spin and oil blows out the plug hole- then gas from the carb is leaking into the sump; or the engine has been tipped for a long time

You should get on that I guess, huh?

you may have a restricted carburetor??

see if unit has a low oil sensor add oil to the end of fill and try again. also check fuel cap for ventilation.