MSI Top - Answered Questions & Fixed Issues - Page 8

Pull out the hard drive and see if it boots, then plug the hard drive in with the machine on. Follow any messages that appear.

It sounds like the frequency referred to is the monitor's frequency. If it's an LCD monitor, the frequency is usually 60Hz. If you are using a VGA cable, it's guessing the frequency and has guessed wrong. The other possibility is that the Railroad Tycoon game sets the screen resolution and frequency to something your monitor is not capable of displaying. It sees a nice graphics card and shoots the settings to the top of the range. If you can change the settings before playing the game, you might get it to work.

If you're lucky, there are screws on the bottom that screw into the hinge. If one is missing, try to find a screw that will go into the opening. If you are daring, you can unscrew the remaining one to see what size it is. If you're not lucky, all of that is inside the laptop. In that cane I recommend duct tape to hold it in place. See if you can find tape the same color as the laptop.

http://download.msi.com/archive/mnu_exe/E7207v2.0.zip

It might be overheating. Make sure the openings on the bottom aren't blocked (set it on a table instead of the carpet or furniture). When the laptop is off, blow air through the vents on the bottom and side to get the dust out of the fan. You can use a vacuum cleaner with the hose connected to where air comes out instead of in.

Because the webcam is built into the lid on the inside, it probably connects with the same cable as the display. If your screen goes blank and won't come back on, it might be worth it to take the laptop apart and reseat the cable. Otherwise, you may want to buy an external webcam and plug it into the USB port.

There are separate buttons for power, one for hi-fi, another for the PC. They are above and below the big knob. The top one is hi-fi, the one below the big knob is PC power. Have you tried both?

As a layman's act, just hit the Ctrl key once or twice (but not with a hammer). or put the keyboard upside down and bang on the back side. There would be some steeple pin went inside and stuck at that key.

Try this link ! https://www.manualagent.com/msi/ms-6712/users-manual/download

You can Download Here it having all drivers reg this mother board

Reinstall the poper wirelss card driver for your device.

dying hard drive problem save what you can to external hard drive

Try a few charge/discharge recharge cycles to see if you get an improvement. If negative, then replace since it is bogus.

why do you continually reformat your pc? Just load it, install correct drivers, and leave it alone. Your baby is long in the tooth and it may be hard to find the drivers for the mo bo as well as your peripherals. Good luck.

Power button directly connects with the motherboard. So first you have to remove the cables that will be connected and then make connection of 6 and 8 pin via any copper wire, if system power on just by connecting the 6 and 8 no. pins then system is ok , you have to replace the power button otherwise there would be motherboard problem. Please confirms once if it works or not. Your comments is much necessary on this

you did not specify the model of your laptop..

indicates that the hard drive is starting to fail save everything to an external hard drive have the system tested by an computer repair shop and if faulty install a solid state hard drive that has no spinning disc also up grade to win 7 operating system as win xp is no longer supported by Microsoft and many other products are not compatible with win xp

I think, the problem is not in your software, in my opinion, your camera needs to be repaired. This is not the first time I heard about such a problem with laptop, and as I know, it is beter to address a professional.

Shut down the laptop..restart in safe mode, once you are in safe mode, try to go to a restore point before the issues started...you should be able to clear this up... 7 ways to boot into Safe Mode in Windows 10 Digital Citizen 5 Ways To Boot Into Safe Mode In Windows 8 1 Need to Start Windows 7 in Safe Mode Here How

It is very easy to bend the pins on a processor. Also you need to make sure that the locking lever is engaged.