Miele Dishwashers - Page 4 - Recent Questions, Troubleshooting & Support

You could buy a no name door seal gasket from any dishwasher parts supplier but you will loose your warranty with Miele. And extended warranties reach up to 6 years if you bought it from a factory authorzed dealer with a factory authorized installion! Call Miele direct. Miele's number is 1-800-843-7231
If you would rather call your local Miele dealer, they'll be more than happy to do help you!

Hi,
Call these guys... I bet they could help you...

http://www.plessers.com/Miele.htm?gclid=CMOi0Kbb9aICFQ-bnAodmE-giQ

heatman101

Take a look here Amazon com Miele Dishwasher parts. Hope you can find something. cheers

hi,

you will have to purchase spare parts from Miele directly or from a miele authorised dealer. you cannot purchase spare parts any other way.

if you look at www.miele.com and chose your country you will find your local Miele dealer or office

You should phone Miele, that is disgraceful. Tell them you want a factory technician to visit. Whomever you got isn't a 'proper' technician, plus you have expended money for items you didn't need replacing. With my Miele washing machine, the engineer attached his laptop to it to diagnose faults. The only thing I have found is making sure the salt cover is tight. These machines go through a self test procedure and if sometimes fails, it aborts the program. F84 Error code Miele\015 As soon as I install the dishwaser I got Error F84\015 Answers : This problem arises because the water inside the washer cannot get out.\015\012 \015\012Firstly......Make sure the salt cover if screwed on tightly (if you have one).\015\012 \015\012Then remove the filter(s) from bottom of the washer and clean.\015\012 \015\012Remove the drain pump cover and remove the one way valve (a ball bearing in a housing) and clean. Take note of rubber cover direction before pulling it out to clean.\015\012 \015\012Make sure the impeller (visible after you remove drain pump cover) is clean and spins ok. It will have a little resistance as you spin with your finger.\015\012 \015\012Make sure all is cleaned properly and it will all work fine again after replacing it all back in and here http://www.appliancehelponline.com/miele.html F84 Slide shutter positioning fault

Hi all,

I have had the same problem. Here is what I've done. Take the door apart (a whole bunch of screws on the side of the door). The front panel will come off and you will see a rubber tube. Take it off and blow it out. Then take the blower out (you need to unscrew the inside of the blower). Take apart the blower and clean it out.

Good luck.

They keep their manuals pretty tight. The only way I know is to know someone there or a service centre that deals with them.

Sgt 48

1. Defective hose 2. Defective connection (if there is one)

I am inclined to believe the Miele repair guy. Maybe a different Miele repair guy would have a different opinion.

https://www.youtube.com/watch?v=GtjphsCQ8CA

F70, waterproof system activated. this means you have water in the bottom pan of the dishwasher. your miele shuts itself off and runs the drain pump continuously any time water leaking is detected. you can pull out the black plastic toe kick under the door. there is a cover panel in the center held on with two t20 screws. you can dry up the water and try to run a cycle. if it works ok, cut back on your detergent by 1/2. if it leaks again, you should probably request service from miele. if you want to try to repair it yourself, let me know and I will help you troubleshoot it further.

It could be a program malfunction. Try changing the program in between a running program - 1. Press the "Start/Stop" button for at least one second. 2. Select the new program using the program selection buttons. 3. Press the "Start/Stop" button. The new program will begin.

If you're removing it consider selling it and have the buyer remove it maybe asking too much eh

But since you have pets in your house, I don't think it will be good. I searched a little bit online. That is good enough i already read it you may check https://vacuumsadvisor.com/miele-c1-vs-c2-vs-c3/ Cheers!

This fault is low pump pressure. more than likely you have some foreign particles jammed in the circulation pump. you would have to remove the unit, tip it on its side and remove the bottom plate and remove the circulation pump and clear the blockage. the unit will start and stop and not work until the pump is clear.

Hi jpkenney, The vent can be replaced. If you open the door and look around the outside of the door, you will see the stainless screws that hold the top & bottom parts of the door on.( the top control section is separate to the rest of the door). Just undo the screws & there you have it. The vent can be replaced easily. Hope this helps.....goodluck.

I hope you didn't buy the new unit. But if the fan screams like a banshee then you probably have the Miele Problem. You have probably read this answer - but here it is again. You may have the Miele problem. The line that drains the fan housing gets plugged with glop. You just take it out and clean it. This happens every year or two. Take off the outside front panel to access the hose that runs from the bottom of the fan down to the dispenser, and lets the water drain out through it to the interior. Clean out that hose as well as you can. Replace. This is an idiotic problem that Miele should have a permanent fix for. Grrrr. The hose cleans out quickly, the problem is getting the front back on. 4 hands make it easier. It slips on when you start close to vertical, then slip in in and down. For putting the screws back in, you might have to use a micro screwdriver to re-align the little clips on the door panel. (You will see what I mean when you do it!) This costs a service call ($100, give or take) to call for service. It can be done at home with no added parts. I think it applies to all Miele dishwashers, and I have now done it several times. As I said before, this is a design fault and should not be necessary! If you have a helper to help contain the mess, you can spray water into the fan area (best is backward through the hose, but try all directions) and catch the runoff. We have done this and it catches a lot of gunk.muck and slop. Doggone design sucks on an otherwise nice machine!!

Mine gives weeks and weeks (daily use) on a setting of 1 or 2. Might be a different size tank? Maybe lower the setting too. How does your glassware feel?

When ours came off (broke off actually) I just got a new one and screwed it in place. Take a look - it may be that it broke along a joint line (ours did) and you can't see that.

Load the rinse aid. Maybe also adjust the dial for rinse aid to 1 number higher.