MicroBoards Computers & Internet - Recent Questions, Troubleshooting & Support

Oui, les pilotes n?cessaires ? l'utilisation du duplicateur Microboards G4 avec Windows 10 sont disponibles sur le site Web du fabricant sous le lien "T?l?chargements et logiciels".

The 306 Error Code is generated when any corresponding process or operation could not be completed successfully by the application.

error 306 may prevent the user from performing the required action or may the application will close unconditionally.

Technical (Deep) Description of Error Code 306:

This is a full Description of ERROR 306: ERROR 306: MCIERR_DEVICE_NOT_INSTALLED.This error is due to .The default facility code ERROR 306: EVENT_APPMGMT_UPGRADE_COMPLETE.This error is due to Application %1 from policy %2 successfully upgraded application %3 from policy %4..The default facility code ERROR 306: SQL_306_severity_16.This error is due to The text ntext and image data types cannot be compared or sorted except when using IS NULL or LIKE operator..The default facility code ERROR 306: ERROR_SECURITY_STREAM_IS_INCONSISTENT.This error is due to The security stream for the given volume is in an inconsistent state. Please run CHKDSK on the volume..The default facility code ERROR 306: CO_E_LOOKUPACCNAMEFAILED.This error is due to The system function LookupAccountName failed .The source of the error code is an RPC subsystem. ERROR 306: STATUS_LOGON_SERVER_CONFLICT.This error is due to The Netlogon service cannot start because another Netlogon service running in the domain conflicts with the specified role. .The default facility code Fixing Error 306 manually is a difficult process and it is not recommend unless you are an expert in this field. click start control panel administrative tools computer management then select event viewer this may vary depending on what operating system you have extend the events there you will see errors in red you will no what exactly what the error was and at what time it occured you might be able work your way through the problem if you need more help with this post a reply with the error message details hope it helps

The Microboards G3 is the worst duplicator I have ever owned. It has worked a total of 4 times, no response from the company, software is terrible and faulty and I'm pretty much over it. Good luck.

You need to click the unknown device icon and search and install the drivers. If you have the disc that came with the machine, then they should be on that. One possibility is that you didn't follow the device installation instructions properly. Missing out some step that is required. So read the installation instructions carefully again. Double check that you haven't missed something. I know that these days for example some printers tell you when to connect them to a PC. Connecting the cable before then can cause problems. One final thing check the cable that connects it. I had one once that though it knew there was a printer, it just couldn't recognise it, just like yours. I replaced the cable and it detected the printer straight away - name, everything!!!

One of the "target" CD-writers is not working -- either the "data" cable is not connected, or the "power" cable is not connected, or the drive itself (either the "spinning" motor, or the "laser") has failed.

Presumably, you don't have to fill "all" the trays, in case you only want to make a few copies of the "source" disk.
So, make a few attempts, with the "source" disk in the "source" drive:
1. put a blank disk into the 1st "target" drive,
leaving the other targets "empty", and press the button.
If it works, then the 1st target drive is OK.
2. put blank disks into the 1st and 2nd "target" drives,
leaving the other targets "empty", and press the button.
If it works, then the 1st and the 2nd target drives are OK.
3. put blank disks into the 1st and 2nd and 3rd "target" drives,
leaving the other targets "empty", and press the button.
If it works, then the 1st and the 2nd and 3rd target drives are OK.

... and so on

If you get a "failure", then you now know which of the "target" drives is the "bad" drive. Either replace that bad drive, or change the cabling inside the unit to "bypass" that bad drive, and put a sticky-label on the face-plate of that drive, saying "do not use this tray".

How does one connect the Wired Toro Rain Sensor, Model 53769 to the Orbit, Model #57979?

Check the print head. May have become derailed. How do the labels look?

What is the model of your MicroBoards drive?

Wrong forum. This is the CD & DVD Forum.

It sounds like it's asking you to install a driver. You might try re-installing that.

The basic troubleshooting steps for a balky program like this would be to reset preferences, if that does not work, then simply uninstall the program and then reinstall it. Please note that this action may delete any presets that you had set up...

Sounds like you're out of Magenta ink. Microboards PFP HC MAGENTA OEM Genuine Inkjet Ink Cartridge Retail

How do I set this system for my watering needs it used to be set and then it stopped working says I need to set

Either the sensor and/or the laser lens inside the tray are dirty, a common fault printers)or you are not aligning the disk properly when placing in the tray. You can try using a CD\DVD cleaning disk and a can of compressed air to blow out dust. If this fails uninstall the printer's drivers and software and reinstall everything from the beginning. If that fails return for repairs. NEVER use stick on disc labels, only use write on discs

System error code 1105 means "Tape could not be partitioned." This error code may also display as "ERROR_PARTITION_FAILURE" or as the value 0x451.

This means that you have selected a drive such as a CD/DVD drive or another drive that is either nothing in it or is not accessible. The source being what you are copying to the DVD burner.

hey john, u must go to the website from Microboards and there u must look for the latest firmware for your unit when u found it than burn it on a cd or dvd and than follow these instructions and u are set to go and the unit must work normal again The Update Firmware feature is used to update the controller firmware. 1. To update the firmware: Place the firmware CD into the reader drive (top). 2. Press the ENT button 3. The display will show the current and update firmware versions, as shown to the right: 4. Press the ENT button to complete the firmware update. 5. The duplicator will reboot automatically after installing the new firmware

please follow the troubleshooting software with the printing. and make the test for clean it. etc. Otherwise, the cartridge can be faulty. God bless you

Reset the printer , turn off, and disconnect the power cord or USB by 1 minutes and reconnect again. and try again.However if the problem persist, unintall the software and reinstall again , and try again.Otherwsie you mus contact to the supplier manufacturer via ONLINE chat for to get support.GOD BLESS YOU