Luminox Watches - Answered Questions & Fixed Issues

a mechanical part needs replacing, unless your have some form of funky split time running? replacing the battery should have reset it though.

How to replace battery Paul Jardin watch can't get back off

take it to a watch maker for a quote and to see if the parts are available

Hi, I've looked at the image you posted, and I think it's a Ronda 515 movement or something very close. If that's the case, do the following. Push the crown fully back to it's normal running position. If it's a screw-down crown then ensure it's unscrewed. Using the tip of a fine pair of tweezers (or similar - perhaps a needle) press lightly on the small depression that you can see in your photo (on the main metal plate of the movement, to the right, just below where the stem enters the mechanism). While pressing on that, gently pull on the crown. If it doesn't release, press a little harder on the depression but please be moderate with the force you use - if you press too hard you may damage the mechanism. If you take enough care, you should be able to remove the crown and stem. To replace it, make sure the movement is correctly aligned in the case and gently press in the stem. If you feel any resistance, then rotate the crown slightly and try again. Again, if you try and force it, you may damage the movement. It is usually not necessary to place any pressure on the depression to reinsert the stem, but if all else fails it won't do any harm. Please let me know how you get on.

If new, just take back and exchange it for another working one.

Try parsecent.com they can get the part or a substitute part, the keeper is not sold separately tho, you would have to buy a complete band...good luck :)

The hand in question is slipping on the spindle that it is attached to. You need to carefully but firmly push it back down on the spindle so it moves. Have to get access to the dial and needles to do this

Have to know the model and serial of the furnace. locate code list usually inside or on the back of a door. Operation sequence= call for heat--inducer blower motor--makes pressure switch--signals board to bring on hsi--after a set time gas valve opens and you have ignition providing current to flame sensor--main blower motor comes on after a set time

go here > http://world.casio.com/wat/download/en/manual/

It should be SOLID TITANIUM Screw down case back.

Click on my profile (escapement), then click on Tips and Tricks. There you will find link to all LUMINOX watch manuals. Rate me, please.

Can get at the following link:

http://www.luminox.com/service/service-centers/

Generally after two years power cell life will over.> are your replaced same battery? check the voltage of power cell _1.5V> Observe that seconds needle giving any jerks? if its trying to move its overhaul faulty, give it to good service center for overhaul.> If its not at all moving at all it might be coil or PCB faulty..

you must have the tools to do that. all you need is a pin remover, pliers and mini hammer.

Try looking at the available manuals listed here:

http://www.luminox.com/service/service-centers/

I don't see one specific to your model; however the manual for Standard / All Models might provide sufficient direction.

If this is not helpful try contacting Luminox directly for assitance as per the following:

http://www.luminox.com/service/contact-us/

I don't know your watch but as an engineer, I would expect there to be a single position where the crown can be pressed in.

Try applying a gentle pressure to the crown while you are slowly rotating it an you may be able to find a spot where it hits and slight depression, (a soft touch required here). When you find this spot, press the crown firmly and then rotate.

If you still have no luck, try speaking to the supplier to find a local repair center who should be able to give you some knowledgeable advice, as I feel sure that you will not be the first person to have this problem.

Altenatively go to http://www.luminox.com/service/service-centers/ to find the information on service center locations and contact numbers.

Hi,
Here is a link that can help you step by step with visuals.
I hope this will be able to help you.
Thank you for choosing Fixya.

This sounds like a typical indication that the battery is running low and should be replaced soon.

Replacing the spring pin is not a problem, however for the band to look as it did originally, the end piece, or end tab - which is now missing, must be replaced. These parts are generally proprietary. You can order one from your local Certified Master Horologist.

You may also consider contacting Luminox. Sometimes, the manufacturers run out of these parts and the whole band must be ordered because that is all that is available.

Contact Luminox Repair Center at 401?946?0920.

You can get a manual by going to http://www.luminox.com/service/service-centers/ and select the one that you need.