Lexmark C - Recent Questions, Troubleshooting & Support

Check your printer settings.

Sometimes if your printer or the program you are printing from has the paper source set to "Letter" it waits for you to press the continue key on the printer which allows you to insert headed note paper before printing.

If it is set to letter, change it to A4 and this should solve your problem

You may need to change this in both the printer settings and/or each program from which you are printing

The 200.16 jam indicates that the input sensor was covered when the printer was powered on or reset, or a cover was opened/closed.

You may also check the following:

1. The paper being used is within specification and has been loaded correctly.

2. Any previous jams have been completely removed.

3. The printing environment is within acceptable temperature and humidity ranges.

4. If the tray was overfilled or a paper jam occurred, sheets of paper may have come off the media stack.

5. If you don

You can unplug the printer from the wall, then leave it off for about 30 seconds then plug it back in. That should reset the printer, if not read what the message says on the screen, or you may have to navigate through the settings to see the error message.

Problem Error: "200.xx Paper Jam"; Error: "200.01 Paper Jam"; Error: "200.11 Paper Jam"; Error: "200.16 Paper Jam"; Error: "200.21 Paper Jam"; Error: "200.22 Paper Jam"; Error: "200.25 Paper Jam"
Solution.

Hope helped.

Here's an article in the Lexmark website on Error: "201 Paper Jam" or "202 Paper Jam". This will guide you on where to locate the cause of the problem. Follow the instructions. But if you're having a really hard time locating it or you need more assistance, don't hesitate to contact Lexmark Technical Support. Thanks.

Pull back the fuser cover ( black upper area) and look for the jam beneath the black roller with paper sticking up - to pull it out

You need to replace the waste toner box, click on the link http://bit.ly/nIzB4G to see instructions on how to go about the procedure.

For further assistance, please contact Lexmark Technical Support.

I presume from your question you have a message that has popped up 'Replace the Waste Toner bottle'. This is a consumable item and will need to be replaced every 30000 pages. Emptying the old one is not recomeded as the toner is very fine, very messy, very hard to get spills out of clothing and so you will need to purchase a replacement (instalation instructions provided)

If it is a new printer call Lexmark, because this is a problem with the magenta printhead. To solve it you need to have some expertise on this printer.

200.16 means the input sensor, it is in the paperfeed assy on the bottom of the printer, is activated. Check if there no paper or pieces of paper in the input sensor or if the input sensor is stuck in "open" position.
Gerrit Jan

Please follow the appended link.

Don

http://support.lexmark.com/index?page=answers&startover=y&locale=en&userlocale=EN_US&productCode=LEXMARK_C782&segment=SUPPORT&question=83.05+ITU+Missing+error+message#1

Please click on the link provided below.

http://bitly.com/nIjA4L

If this does not resolve the issue, please try to reseat the printhead cable.

Turn the printer off, and remove the rear. Check the cable at JMIRR1 for shield. proper connection to the controller board, the printhead cable for pinch points, and the cable

or connector for any other damage.

Remove the toner cartridge, and inspect the lenses on the toner meter cycle (TMC) card.It is positioned on the right side of the toner cartridges
Are the lenses blocked, or dirty? Clean them
If damaged replace them

Open up the right front cover, open up the right upper cover, open up the right lower cover. the waste toner cartridge is there facing you, it should just pull out.
Part number C540x75G
One on ebay uk Item number 180577646764

The error indicates that the system board's on-board memory has failed. This usually requires a service call but you can try to turn off the printer, then turn on after 15 seconds. If the problem continues, I strongly suggest you contact Lexmark technical support or an authorized service provider for assistance. You may need to know your printer's model type and the serial number when calling for service. Thanks.

Have you tried checking that tray 2 has the same paper type as tray 1. If your machine is network attached, you can access the embedded web server (where device settings can be adjusted) by entering the device IP address into a browser. Find the web address from the machine by going to menu (key icon), reports, then arrow over to network set up page. NSP is a 1 page report which will tell you the IP address. Go to a web browser and type in that IP address. Should take you to your device web page. From that page you can change the device settings (click on settings and then paper menu). Check to be sure that the same paper type is set for both tray 1 and tray 2 (and be sure that tray 2 is showing up on the list). I had to power the printer back on for it to recognize tray 2. Hope it helps

When I have seen this error in the field, I have cured it by updating the firmware. Lexmark has a paper in their Knowledge Base on 900 errors:
http://support.lexmark.com/cgi-perl/knowledgebase.cgi?ccs=229:1:0:556:0:0&framed=&docid=ENUS22164&relevance=1

Go through the suggested steps to try to narrow the problem down.

But if it needs a firmware update:

http://support.lexmark.com/printerfirmware/

Use code: Isfap129 to download the package the C530dn.

Hope this helps!

900 Service RIP errors are usually a firmware failure. Upgrade to the latest firmware from Lexmark. This link is for the C52X network model:

http://downloads.lexmark.com/perl/downloads/downloads.cgi

900 errors usually point to fuser or fuser related component failure.

Please have the printer serviced.

removed memory off the system board restarted printer. came up to an error no memory found.
powered down and reinstalled memory on board in a different slot and restarted unit...
NO ERRORS......