Lexmark Computers & Internet - Page 8 - Popular Questions, Answers, Tips & Manuals

If this is also happening when you're printing from your computer, then it could be a problem with your printhead. Try to update the firmware of your printer. Just go to http://bit.ly/ghfW8H to download the firmware update.After running the firmware update, perform a maintenance on the cartridges. To do that, on the control panel of your printer, press on Setup > Maintenance > Deep Clean Printhead.If you still see the same problem and your printer is still under warranty, contact our technical support team to have the printhead replaced.

yes

Assign An Ip Address; Step 3: Print A Network Setup Page ...

https://www.manualslib.com > ... > Quick reference Lexmark MarkNet X2000 Series Manual Online: step 2: assign an ip address, Step 3: Print A Network Setup Page. '' To View This Information.

MarkNet external print servers - Lexmark

http://publications.lexmark.com > eng > mnextset PDF 3 Set the IP address, netmask and gateway in the MarkNet. To do this, telnet to port 9000 on the MarkNet print server by typing a command similar to.

• MarkNet X2000 Series External Print Server Quick Reference

  http://publications.lexmark.com > mnpset_web PDF If your network is not using DHCP, you must manually assign an IP address. One of the easiest ways is to use the Print Server Setup. Utility on the drivers CD.

what sort of computer ?http://download.cnet.com/lexmark-x1100-series/3000-2118_4-62934.htmlhttp://www.filebuzz.com/findsoftware/Universal_Software_For_All_Webcams/1.html http://www.filebuzz.com/findsoftware/Webcam_Driver_For_All_Webcams/1.html

rather doing a driver hunt which can take hours

http://download.cnet.com/slimdrivers-free/3000-18513_4-75279940.html

it might take some time being a freeware driver solution

note: it will find all of your outdated drivers

this is a free driver solutions this will automatically search for and find the correct driver you will have to update every driver individually once you update you might be asked whether you want to restart or make a system restore point click no to both of these then continue updating each driver free then restart once all of the drivers have been updated hope this helps

The Lexmark X4975 Professional is a multifunction thermal inkjet printer that not only prints documents and photos, but also makes two-sided printouts, scans and copies materials and accepts line-connected or wireless device print requests. Three color ink cartridges--cyan, magenta and yellow--and a single black cartridge rest inside an ink cartridge carrier. Printer cartridge replacement is not difficult. Each cartridge is secured in place with a cartridge carrier lid that opens with the simple press of a lever.

• Turn on the Lexmark X4975 printer. Lift up the entire scanner unit to rest in an open, angled position that reveals the interior of the printer.

• 2

  Press down on the lever in front of the printer cartridge that you need to replace to open the cartridge carrier lid.

  • 3 Pull the old cartridge from its slot in the carrier.

  • 4

    Grasp the tab attached to the tape covering the electrical contacts and ink nozzles on the back and bottom of the replacement printer cartridge. Pull the tape away from the cartridge carefully without touching the contacts or nozzles.

  • 5

    Insert the cartridge into the empty slot--the electrical contacts facing the back of the slot inserted before the front of the cartridge.

  • 6

    Flip the cartridge carrier lid over the top of the cartridge and then push down on the top of the lid until you feel the lever lock the lid in place.

  • 7

    Repeat the replacement process with the other printer cartridge if necessary. Lower the scanner back into position when finished.

    Increase Engine Horsepower.

There are two possible fixes.Download the latest firmware update by CLICKING HEREThe following is provided by courtesy of Lexmark: Problem Vertical lines; Auto document feeder scan anomaly; ADF scanning problem; Scan issue; Scanner issue; Visible line; Streaks show on page; solid line down the page; Top to bottom line; Smudge runs down the page; Opaque line; Broken line; Bar all the way down the page Solution Overview

This article provides the self-diagnostic steps necessary to evaluate top-to-bottom streaks that appear when copying or scanning.

Important! This is seldom a scanner hardware failure.

The main reason for this anomaly is debris or marks on the scanner glass that is used for Auto document feeder (ADF) page scans.

Printed or Scanned Page Illustration

Who should consider this article?

Any user of an MFP or All-In-One printer experiencing the following symptoms:

• -Vertical lines only when using the Autodocument Feeder (ADF).
• -Observed with any type of scan job (e-mail, ftp, solutions, fax).
• -However, normal expected output when the page is scanned from the scanner flatbed.

ADF scan behavior

Think of it this way:

• -The page is pulled from the ADF.
• -The moving page slides across an ADF-designated portion of glass.
• -The image sensor, which is located under the glass, reads and interprets the moving page's contents.
• -Contamination on this ADF glass is seen by the image sensor for the entire length of the page.
• -The image processor interprets the image sensor's repeated capture of this contamination as a vertical solid line.
• -Any ADF scan function now exhibits a vertical line.

Suggested Diagnosis and Fix

Step Action 1 Locate the portion of the glass designated for ADF scans. HINT: The glass location differs by model. This area is often separate from the scanner flatbed. Please reference User's Guide for more information if you are having a difficult time locating this designated area. 2 Perform a visual inspection for any of the following recurring culprits:

• -Clear adhesive tape
• -Glue
• -Ink pen
• -Paper
• -Marker
• -White out
• -Staples
• -Environmental dust or dirt

HINT: Ink marks can be especially hard to see and almost translucent at first sight. However, the image sensor (CCD) registers them as a mark. 3 Use a clean, soft, moistened cloth to thoroughly clean and remove any marks or debris. 4 Inspect the underbelly or underside of the ADF for any marks or debris. 5 Perform another scan to see if cleaning the glass alleviated the issue. 6 Repeat the procedure if a vertical line still appears. Remember! Printing and scanning from the scanner flatbed work fine. 7 This time, place an intentional mark on a blank sheet of paper and take note of its location. Now place that sheet of paper in the ADF and make a copy. 8 Evaluate the distance of the vertical line to the your mark. 9 Inspect that area of the glass for further debris or marks and clean as necessary.

Other Possibilities If... Then... Vertical lines appear only when printing... Consider other printer-related topics such as toner cartridge, charge roll, photoconductor, transfer roll, or fuser. Contact Lexmark Technical Support. Vertical lines appear when you lay the page on the flatbed... Consider other printer-related topics such as toner cartridge, charge roll, photoconductor, transfer roll, or fuser. Contact Lexmark Technical Support. Vertical lines appear on ADF-fed printed copies, but they do not appear on scan-to-network [e-mail, FTP, folder (PC), solutions]... Consider other printer-related topics such as toner cartridge, charge roll, photoconductor, transfer roll, or fuser. Contact Lexmark Technical Support.

check in tracks for paper pieces or dust or other small lint that can cause a one side imbalance on a lexmark

Check if your printer is up to date. Just go to http://bit.ly/ghfW8H to download the firmware update.Also, make sure that you're using genuine Lexmark cartridges. If there's an error message on your screen that your black ink is low even if you replaced it, you won't be able to print or scan. It will send a busy signal or communication not available to your computer. If this is the case, replace the cartridge.If it still doesn't work work, try to reinstall the software: http://bit.ly/d3ftso

There is no windows 7 Driver but sometimes the windows Vista one will work. Below is the link to the files.Link:

click start control panel administrive tools computer management device manager scroll to ports(COM&LPT) + to expand you should see a communication port and Ecp printer port you might see a yellow? ! question exclamation mark or a red X this will mean you need to install a new driver for this device right click you will have options to update driver,disable,uninstall or select properties again you will have the similiar options also you can troubleshoot the device
if you dont have the driver you will need to download one
http://download.cnet.com/lexmark-x1100-series/3000-2118_4-62934.html
The Lexmark X1100 Series All-In-One combines the functionality of an inkjet printer, a scanner, a copier, and a fax machine all into a single, multifunction device, making it one of the most exciting products on the market today
hope this helps you

Welcome to Fixya

Thank you for bringing up the problem to our attention. To serve you better, could you please provide the exact brand and model of the printer that you are using. This will help me in identify possible cause and what solution we need to apply in order to fix the problem.

Your response will be greatly appreciated.

Thank you for using Fixya! If you need further help, reach me via phone at https://www.6ya.com/expert/elixirjose_00375ea24bd8141b

You can download the Lexmark printer drivers from theirsupport WEB site. Please click on this link and select your model printer todownload :-http://support.lexmark.com/index?page=home&locale=EN&userlocale=EN_US&segment=DOWNLOAD

hi the barcode scanner is verry sinsetive...will u bring it the HP or Cannon
Printer expert technician...thank's

make sure the ip of the client computer is correctly assigned to server

try to replace other usb cable cord on printer..

Go to the program files and look in the peinter file for scan folder it will be in there

Hi ,
Go to google and type in make and model , it will bring up a page with what your looking for ,
ebay is a good source to .......................Roy

Connecting your jump drive to any USB port , of your computer should add an additionnal Drive to the lost of your device under "my Computer,
Once tou located this drive and it's letter you can simply copy paste any file or folder from your computer into it.
Hope this answers all your questions Please remember to Rate/vote for any solution that helps you out. Leave a comment if you need more help. Thanks for using Fixya

Optical character recognition, usually abbreviated to OCR. It is the mechanical or electronic translation of scanned images of handwritten, typewritten or printed text into machine-encoded text. In simple terms means your "scanner software" for your scanner device may be corrupted if the "OCR" is missing due to several reasons eg. fFles changes due to installations of software, Malware, Spwares or virus on you PC, etc....

Try uninstalling & reinstalling the Device setup i.e. "Drivers & Software" from the CD/DVD that comes with your Device.

Hope it helps.

Any drivers you need can be found on the lexmark website. Note that some printers need the software installed before hooking up the printer. I'd try to install the printer first. The software will tell you if the printer needs to be connected.