KitchenAid Ovens - Page 4 - Recent Questions, Troubleshooting & Support

You will need a new igniter module. The igniter module is told to spark by the control panel. There is also a flame detection for electronic start and that could be bad too.

when you put it into self clean the oven gets up to 1000 degrees and it will damage the electronics in the oven and it sounds like this happened to you,i've been telling everyone i know not to do this until after the holidays in case something like this happens you won't have a stove for the holidays and also i tell them to never use the self clean use easy off works just as good,sorry to hear about you stove,if this is an older stove most likely you won't be able to even get a new clock assy. but you can send your old clock assy. out to get rebuilt to http://generaltimerepairs.com/ you either do this yourself or get someone to remove the old clock assy. make a wire diagram,send the clock assy. out to have it rebuilt they send it back to you and you reinstall it and don't use the self clean again.one more thing i think there's a thermal fuse in the ka and that could have popped,you have to check it with a meter hope this helps and good luck.

That is where the vent is. You should feel some hot air there. If you do not feel the air that is the time to worry. If you have any other questions please feel free to ask.

Try setting the temp 25 degrees lower than what is called for. This is a common issue with convection ovens.

I found the answer by checking the Kitchenaid website to find the manual. My model is KEMS308sss04, this is found on the right door frame. Website is: http://shop.kitchenaid.com/assets/pdfs/literature/Use%20and%20Care%20Guide%20-%20W10162223.pdf
You can preheat oven, but then turn off to set thermometer. Put probe in food. Put food in oven and plug in probe. The digital light asks for the temperature you want, type it in. Then the cooking method. I used convection bake at 325. Hit START. (The first time I didn't stop the oven and it didn't work. After stopping everything and starting with the probe before turning on the oven, it worked perfectly. Good Luck.

Either oven sensor is bad or control board is bad.

Any gas cooker has a thermocouple that keeps the gas valve open; if the thermocouple no longer generates current (which feeds the coil of an electromagnet) then the gas valve closes and the flame will go out. So check thermocouple. In normal conditions the voltage generate by the thermocouple is low but the current is high.

Element burnt out or control board is bad.

I think this is a cheapest and eat way to fix your oven doors... Otherwise there are 2 spring type locks of the door that starts getting old day by day ... You have to change the pair of lock only

What make and model is it?

F2 E1 means that the keypad cable is unplugged.
Gain access to the control panel and keypad. Check keypad connector for firm connections. Keypad connects to the control board. Press CANCEL. If error code returns after 60 seconds, the keypad needs to be replaced. If your control board and keypad are incorporated as one unit, then the control board needs to be replaced.

If you've determined the keypad on your Kitchenaid oven, range, or wall microwave is faulty and youre searching for an obsolete part, http://www.FixYourBoard.com has replacements by Ledgestone Technologies. These units are backed with a 2 year warranty. Save your $ and save your oven from the landfill. We have you covered! Call 512-355-1108 for more information and to order. We're happy to help you solve your problem! FixYourBoard.com

F1 - E1
EEPROM checksum error

1.
Disconnect power for at least 30 seconds.
2. Re-apply power and observe for
at least one minute.
3. If code re-appears, replace control board (also
called ERC or clock).

Note: Applies to all F1-E...
codes except F1-E3.

If you've determined the keypad on your Kitchenaid oven, range, or wall microwave is faulty and youre searching for an obsolete part, http://www.FixYourBoard.com has replacements by Ledgestone Technologies. These units are backed with a 2 year warranty. Save your $ and save your oven from the landfill. We have you covered! Call 512-355-1108 for more information and to order. We're happy to help you solve your problem!

Hello & Welcome to FixYa

F2-E0 error code indicates a open/shorted oven temperature sensor and to solve this problem the sensor needs replacement. If you wan to be sure before replacing the sensor then you can test it with a voltmeter for around 1100ohms....if it reads more then this then it needs replacement however, if the reading is around or less then 1100ohms then it is the control board that needs replacement. Please get back to me if you have any other questions.

Kevin