KitchenAid Cooktops - Popular Questions, Answers, Tips & Manuals

0helpful
1answer

My Kitchen aid cooktop model number KECC667BBL won't turn on

Mis-wired or the new control panel is faulty. Call them back, it is under repair warranty. The parts aren't cheap! https://www.searspartsdirect.com/model/41v4g0ja62-000593/kitchenaid-kecc667bbl01-electric-cooktop-parts ..
2/9/2022 5:32:15 PM • KitchenAid... • 129 views • 0 helpful votes
0helpful
2answers

My intermittent ignition device on kitchen aid stove is not clicking.

igniter failed
1/30/2022 9:18:59 PM • KitchenAid... • 70 views • 0 helpful votes
2helpful
1answer

Kitchenaid Electric cooktop KECCD805HBL3 Left front 8" eye only cycles at high heat no matter what the setting. Do I need a new eye or switch or both?

Almost certainly the switch, not the element, Had the same problem on a different stove - went to 10 no matter what the knob was set to. Here is a parts list, you should be able to get the part from a local appliance part seller. I used ReliableParts in my town. https://www.partselect.com/ModelSections.aspx?ModelID=815598&ModelNum=KECD805HBL3&mfgModelNum=&ManufactureID=3&Selected=ZPGZLZRB&Position=2&mfg=Whirlpool&Type=Cooktop&Mark=2
10/31/2019 9:09:21 PM • KitchenAid... • 212 views • 2 helpful votes
0helpful
1answer

Had a spill on my kitchenaid KGCC566RBL gas glass cooktop. some dripped in the knobs and under the glass top. How do I access that to clean?

I found this...... https://www.doityourself.com/stry/how-to-replace-a-glass-cooktop-on-kitchenaid-ranges I read it and it's on replacing but the top comes out. Gloves are a good idea too. Cut power at the breaker. unless easy access to the wiring/plug. Hope this helps you. Have a good evening.
2/2/2018 12:36:03 AM • KitchenAid... • 416 views • 0 helpful votes
0helpful
1answer

My whirlpool (KitchenAid) induction cooktop works sometimes and other times will. The power comes on but when I try to turn on the burner it beeps and starts flashing. There are no error codes showing

It is likely the computer in the control board I have seen this many times. It is really hard to get the factory to think this cause it's new and it is expensive. But you have checked the power so there is not much more that it could be
8/7/2017 4:12:03 AM • KitchenAid 30"... • 495 views • 0 helpful votes
0helpful
1answer

I have a comercial style

You should make sure the range matches the correct gas, if you have to change orifice you must get the correct ones from manufacture do not use any other orifice always unplug electricity before attempting to repair on any electrical appliance
8/19/2017 5:45:03 PM • KitchenAid 30... • 287 views • 0 helpful votes
0helpful
1answer

Constant sparking

I don't have a Thermador cooktop but here is ma taught. Could you unplug the two faulty igniters and see if problem remained Could you plug one of the faulty igniter at the location of a good one. The goal is to isolate the problem. Is it the igniter or the electronic board. Faulty ground problem may occur also after an spillover on the stove. In that case, use a cotton swab dipped in scrubbing alcool and clean the spark area on the igniter and the burner. Good luck
3/31/2017 3:00:08 AM • KitchenAid 31... • 599 views • 0 helpful votes
0helpful
1answer
0helpful
1answer

I'm installing a kitchen aid cooktop. How do you attatch brackets on cooktop installation?

They go under the counter and they are screwed in place
2/6/2017 10:05:13 PM • KitchenAid... • 340 views • 0 helpful votes
0helpful
1answer

After we had a tech to fix the glass top and one burner, the f1:e1 code came out and kept beeping. I was told it could be the control board problem. Could it be loosen wiring problem too?

Hi, Need model number of your range to answer this question. Is this gas or electric? Is this a freestanding range or cooktop because I only can find information on ranges with this fault code given. All should EEPROM communication error which is a communication error on start up. when the top was damaged was the unit being used? Was water or liquid a factor when this damage happened? A loose wire would be a different error code or fault code like a F2 - E1 or E2, not your code given. I hope this helps, need more information. Thanks I’m happy to help further over the phone at https://www.6ya.com/expert/gere_bf68e6055dd61249
4/17/2016 5:25:27 PM • KitchenAid... • 465 views • 0 helpful votes
0helpful
1answer

After we had a tech replacing a new glass cooktop and one burner, the f1:e1 came out and kept beeping. could it be loosen wire or the problem of the control board?

Call the repair company to come back. It's possible he didn't hook something up right. ...
4/17/2016 5:29:12 PM • KitchenAid... • 294 views • 0 helpful votes
0helpful
1answer

This is not the oven it is the cook top. After it was accidently turned all off and locked I can not get it to turn back on.

To Unlock Cooktop: Touch and hold the CONTROL LOCK/ ALL OFF keypad for 5 seconds.
12/6/2015 10:45:19 PM • KitchenAid... • 461 views • 0 helpful votes
0helpful
3answers

Where can I get a service manual?

Kitchenaid KSC24C8EYY02 Manuals

www.manualslib.com > Brands > KITCHENAID Manuals > Refrigerator Kitchenaid KSC24C8EYY02 Pdf User Manuals. View online or download Kitchenaid KSC24C8EYY02 Installation Instructions Manual, User Instructions.
9/11/2015 1:06:02 AM • KitchenAid... • 1,084 views • 0 helpful votes
1helpful
1answer

Kitchenid 36" gas cooktop: burners ignite fine, but after a few minutes a buzzing sound can be heard from somewhere underneath the cooktop.

If it does it with each individual burner 'ON', it may be something in the gas line.
7/6/2015 4:30:34 PM • KitchenAid... • 248 views • 1 helpful votes
1helpful
1answer

My Kitchenaid cooktop is not working, but is beeping. How can I turn it off?

Have u tried unplugging it for about 10 minutes then plugging it back in? Sometimes doing thus can reset it. It is only a quick fix and a qualified serviceman should called to completely fix the problem.
11/27/2014 6:40:54 PM • KitchenAid... • 449 views • 1 helpful votes
0helpful
1answer

Kitchaid electric range display PF what to do

PF indicates a Power Failure. Turn off the power supply (for 30 seconds or more) to the unit and then back on, select/touch the range cancel/clear pad and reset the clock. The range should work again, unless there was damage to the control during the power interruption.
10/5/2014 2:26:21 PM • KitchenAid... • 455 views • 0 helpful votes
0helpful
1answer

I Have a kitchenaid cooktop and the igniter of the largest burner of the five would not light or sometimes it would light for a few minutes and it start clicking until i turn off the burner. What sho

full repair of kitchenaid cooktop in one video. spark module, switches, igniters and jets replace.
7/13/2014 6:39:15 AM • KitchenAid 30... • 1,119 views • 0 helpful votes
0helpful
1answer

After installoing a surface igniter why will one burner not ignite

There might be many reasons. Wiring, spark module or spark switch. Here is video which can give You an Idea on Whats might be wrong. Thanks.
8/7/2014 11:30:05 PM • KitchenAid... • 257 views • 0 helpful votes
0helpful
1answer

How do I remove based grill

You should be able to get your fingers behind it, either on both ends or underneath. You MAY POSSIBLY need to open the freezer door a little and hook your fingers behind the top of the grille.
7/31/2014 4:42:03 PM • KitchenAid... • 148 views • 0 helpful votes
Not finding what you are looking for?
KitchenAid Logo

281 questions posted

Ask a Question

Usually answered in minutes!

Top KitchenAid Cooktops Experts

john h

Level 3 Expert

29494 Answers

ADMIN Andrew
ADMIN Andrew

Level 3 Expert

66950 Answers

Are you a KitchenAid Cooktop Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...