Kenwood Food Mixers - Popular Questions, Answers, Tips & Manuals

If in the UK try espares; https://www.espares.co.uk/search/mo2748942/kenwood/blenders---mixers---juicers/km631-major-silver-+-at337 They may ship abroad ... I don't know, I am UK based.

Check the power supply: Ensure that the food processor is properly plugged into a functioning power outlet. Sometimes, a loose connection or a tripped circuit breaker can cause power issues.

Safety interlock system: The Kenwood Multipro 910 food processor usually has a safety interlock system that ensures all parts are properly assembled before it can start. Check if all the components, such as the bowl, lid, and blade, are correctly locked into place. If any of the parts are not properly assembled, the food processor may not work.

Motor overload protection: If you have been using the food processor for an extended period or with heavy ingredients, the motor may have overheated and triggered the overload protection mechanism. In this case, you will need to allow the motor to cool down for some time before it can restart.

Fuse or circuit breaker: Some food processors have a built-in fuse or circuit breaker that protects the motor from electrical surges. Check if your food processor has a fuse and ensure that it is intact. If it has a circuit breaker, reset it if necessary.

Mechanical issues: If none of the above steps resolve the problem, there might be a mechanical issue with the food processor. It could be a faulty motor, broken wiring, or a malfunctioning switch. In such cases, it is advisable to contact the Kenwood customer support or take the appliance to an authorized service center for repair.

Restoration https://www.google.com/search?q=Restoring+Kenwood+major+a707b Parts Diagram https://www.google.com/search?q=kenwood+major+a707b+parts+diagram Great information in the last link. You have to scroll a long way down the target page that is referenced here. https://hyperentang.wordpress.com/page/2/

Parts Distributors ' KENWOOD USA

https://www.kenwood.com > usa > Support > Parts_Dist... Replacement parts manuals and certain accessories not available from our Store may be ordered through the KENWOOD Authorized Parts Distributors listed below ... Missing: a707b ‎' Must include: a707b

A700 - Kenwood Chef Restore

https://www.kenwoodchefrestore.co.uk > Kenwood Che... A700 - Chef. Made in England - Kenwood, Woking, Surrey. ... Parts are obsolete. A -300 watt motor with centrifugal ... Download Instruction Manual - Here. Missing: a707b ‎' Must include: a707b

Kenwood chef A701A schematics - iFixit

https://www.ifixit.com > Answers > View > Kenwood+c... Sep 20, 2014 - Where can I find the schematics for a Kenwood chef model A701A in order to restore this machine?. Mike Jordan. Answer this question I have this ... 4 answers · 6 votes: I have probed my A701A and looked at one of the relevant patents. My provis ..

Question edited for clarity. Question moved from Cars and Trucks to model category. The OP, George supplies the answer. Update solved: problem was the tiny speed control sensor mounted above on the motor with three cables.

It sounds like there may be an issue with the motor in your Kenwood Chef Premier mixer. This could be caused by a variety of factors, such as a malfunctioning motor, a problem with the drive belt or gears, or an issue with the electrical components of the mixer. To troubleshoot the problem, you may want to try cleaning and lubricating the drive belt and gears, as well as checking the electrical connections and fuses.

Help in the link including from Kenwood themselves. It is likely to be the selector, the control board or the motor. Take it in for Dealer Service. https://www.google.com/search?q=Kenwood+kmix+doesn%27t+start ..

If you have a multi meter check the box caps and resistors for KM 2XX series then replace it whenever required. Some may differ in values like 0.15uF 275x2, 0.33uF 275X2 or 0.47uF 275X2 then resistors may also differ with different models but common to have 1.1k ohms 2watts. Also if caps are open it is good to check the 600V triac and replace it when giving out lower output. I also advise to clean the commutator esp when is is sparking a lot, you may use light sanding and clean it after. Check also if the tachometer is good, there is a resistor-like-coil hidden under a plastic tab with 2 wires. This gives feedback and via a magnet attached to the shaft. Check the motor brush if it is good or worn out. Lastly check all the switches because if one of them is not working properly you wont be able to let the motor run.

Take your pick :>D https://manualzz.com/doc/24514755/a901e-repair-instructions https://www.manualslib.com/manual/1239313/Kenwood-Hm-901.html https://www.google.com/search?q=Kenwood+a+901+repair+manual ..

I use white food safe grease. Here is an example; https://www.ebay.co.uk/itm/391996333570?epid=25018211366&hash=item5b44cd5e02:g:NlUAAOSwoeVdxAPv

it possibly stripped the coupler

We are FIXYA dot com, we aren't Kenwood Chef, we aren't who you think we are. There can be two reasons for a Kenwood Chef to run but not turn the beaters. The most likely one is that the Drive belt has broken. Or You have strained the beaters and you have sheared the shear pin in the drive shaft. It is there to save you damaging the motor and gearbox. Take the top cover off https://www.google.com/search?safe=off&rlz=1C1QJDB_enCA643CA644&sxsrf=ALeKk00zPgmBhh6OuyNypTqtItnqQKaGMw%3A1615571990471&ei=FqxLYIuQHJDQsAW1nJyICw&q=Kenwood+chef+beaters+not+turning ..

Parts Schematics are the closest you will get to that. https://www.google.com/search?q=kenwood+km631+parts+schematic Some videos that MAY help https://www.google.com/search?safe=off&rlz=1C1QJDB_enCA643CA644&sxsrf=ALeKk01xN5zI1Yg5Oztcp7qpSbtNg9hAUg%3A1612909753535&ei=uQwjYLWfIMHksAXdja-4AQ&q=kenwood+km631+rebuild .. ..

Kitchen Aid suggests putting a dime in the bowl and turning the mixer on low. If the beater attachment pushes the dime around the bowl, the attachment is too low. If dime doesn't move, the attachment height is too high. When the attachment height is just right, the dime will only move a little.

Try fleabay.

A white or clear lithium grease. Do not cake it on but enough to get into all of the cogs/worm gears.

Need to take a 2x4 balance it between the outlet for the grass and maybe a pair of vise scrips and then try to take it off.

Sounds as if the amplifier is overheating? Does it do this at all volume levels or only when turned up to higher levels- if so it's likely the amplifier inside of the receiver.

Any idea how many operational hours? I suspect motor brushes but can be other.

sounds like the brushes need replacing see link for them https://www.partmaster.co.uk/chef-food-mixers/chef-range/km001/catalogue.pl?shop=kenwood&path=590704,71679&model_ref=440446&page=3

If you do not know what you are doing it is better to throw it away and get a new one. You could get electrocuted if you try yourself. Probably cost more than a new one to get someone to repair it.