Press, High temp wash, heated dry, High temp wash, heated dry, High temp wash, Heated dry
The panel should all light up at which point you need to press cancel. This will reset the control board if it can be reset. If you do not have a "heated dry" button use "saver dry" or "air dry"
Give this a try to see if it'll reset...disconect power to it for 30 seconds while no power press power button for 10 seconds then press the start/pause button for 10 seconds. Plug in or turn breaker back on and see if it reset.
Best to You
To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a timer control knob, turn the knob around and back to any position other than final spin for the interrupted cycle. Then, restore power.
One of your parts was faulty on delivery. Due to the cost of control boards, I would always advice a service call so that you get the correct diagnosis and warranty on the part and the labour if it goes wrong. Unscrupulous dealers will sell parts from scrapped machines that haven't been tested. eBay is the worst culprit.
..
To clean your Kenmore Elite SM 9711174 washing machine, you can follow these steps: 1. Clean the exterior of the machine: Wipe down the exterior of the washing machine with a damp cloth and mild detergent. Be sure to dry it thoroughly to prevent any water damage. 2. Clean the drum: Mix a solution of 1/4 cup of baking soda and 1/4 cup of water and pour it into the detergent dispenser. Run the machine on the hottest and longest cycle with an extra rinse. This will help to remove any built-up detergent residue or mildew from the drum. 3. Clean the detergent dispenser: Remove the detergent dispenser and soak it in warm, soapy water for 10-15 minutes. Use a soft-bristled brush to scrub away any buildup or debris, and rinse it thoroughly before replacing it. 4. Clean the lint filter: The lint filter is located near the bottom of the machine. Remove it and rinse it under running water to remove any lint or debris. If the filter is particularly dirty, soak it in warm, soapy water for a few minutes before rinsing it. 5. Run a cleaning cycle: Some washing machines have a self-cleaning cycle that you can use to help remove any buildup or mildew. Check the user manual for instructions on how to run a cleaning cycle on your specific machine.
By following these steps, you should be able to clean your Kenmore Elite SM 9711174 washing machine and keep it running smoothly.
Question edited for clarity.
LE, not L3?
LE code on Kenmore washer
An LE error code is displayed when the tub fails to spin. The error code indicates that the motor can't operate properly because you've overloaded the washing machine, or a foreign object is stuck in the tub.
Nov 21, 2022
Did you check the gauze strainer in the water connector.
To test for voltage, use your multimeter. Turn the machine on and set a cycle, then carefully use the probes to check for voltage.
Question edited for clarity, add some CAPS and punctuation!
It is certainly a drainage issue. Check the connectors on the main board or timer dial. Also check the drain pump actually works.
@ronhurley the error code "OE" is a "Drain error " and it is initiated by your washer not having fully drained in 10 minutes. Most common cause is a clogged filter.
Jan 17, 2016
The E2F2 error code on a Kenmore Elite washing machine typically indicates a problem with the communication between the control board and the motor control board. This could be caused by a faulty control board, a loose or damaged wire connection, or a problem with the motor control board.
Here are some steps you can take to troubleshoot the issue:
Unplug the washing machine for a few minutes and then plug it back in to reset the control board.
Check the wire connections between the control board and the motor control board. Make sure they are secure and free from damage.
If the wire connections are okay, you may need to replace one or both of the control boards. You can find replacement parts online or through a local appliance repair shop.
If you are not comfortable working with electrical components, it's best to contact a professional appliance repair technician to diagnose and fix the problem.
The E24 error code on a Kenmore dishwasher model 630.1390 typically indicates a problem with the drain pump or the drain hose. This can cause the dishwasher to start adding water but then shut off and display the E24 error message.
Here are some steps you can try to fix the issue:
Check the drain hose for any clogs or blockages. Make sure the hose is not kinked or bent and that it is properly connected to the garbage disposal or drain.
Inspect the drain pump for any debris or foreign objects. Clean out the pump, if necessary.
Check the air gap on the dishwasher. Make sure it is not clogged or blocked.
Inspect the control board and check for any error messages.
Power off the dishwasher and unplug it for 10 minutes to reset the electronic control board.
Make sure the dishwasher is level and that the legs are adjusted properly.
If the problem persists even after trying these steps, it might be best to contact a professional technician for further diagnosis and repair.
https://kenmoresewingmanuals.com > product > kenmo...
This is the complete Kenmore 158.19310 19311 sewing machine instruction and user manual. Clear pages make it easy to print yourself. 63 pages. PDF download.
US$5.95
https://sewconsult.com > product > kenmore-158-1931...
This is the complete Kenmore 158.19310 19311 sewing machine instruction and user manual. Clear pages make it easy to print yourself. 63 pages. PDF download.
US$5.95 · In stock
https://www.ebay.com > itm
Kenmore Sewing Machine Manual on CD. Excellent QUALITY color COPY of USER'S GUIDE for Kenmore 1931, 158.19310 and 158.19311. Original manual was printed in ...
US$10.75 · In stock
If your Kenmore washer series 400 model 22102 is dripping water in the tub after the cycle is complete, there could be a few potential causes. Here are some things to check:
Water valve: The dripping could be due to a faulty water inlet valve. This valve controls the flow of water into the machine and if it's not closing properly, water can continue to drip into the tub even when the cycle is complete. You may need to replace the water inlet valve to fix the issue.
Water level sensor: Another potential cause of dripping could be a malfunctioning water level sensor. This sensor tells the washer when the tub is full and it's time to stop filling with water. If the sensor is faulty, it may not be accurately detecting the water level, which could lead to dripping. You may need to replace the water level sensor to fix the issue.
Drain hose: If the washer is not properly draining, it could also lead to dripping after the cycle is complete. Check the drain hose for any kinks or clogs that could be preventing water from draining properly. You may need to clean out the drain hose or replace it if it's damaged.
Overloading: If you're overloading the washer with too much laundry, it could be causing water to overflow and drip into the tub after the cycle is complete. Make sure you're following the manufacturer's guidelines for load size to avoid overloading the machine.
If you're unsure of how to diagnose or fix the issue, it may be best to consult a professional technician or reach out to the manufacturer for assistance.
t's possible that there is an issue with the door lock mechanism or the door lock sensor. The fact that the door locks but nothing else happens suggests that the washer is not detecting that the door is locked properly. Here are a few things you can try:
Check the door lock mechanism: Make sure that the door lock mechanism is clean and free of any debris or obstructions. Try manually engaging and disengaging the door lock a few times to make sure that it is working properly.
Check the door lock sensor: The door lock sensor is a small switch located near the door lock mechanism. Make sure that it is clean and properly aligned. You can try pressing it manually to see if it is working properly.
Check the wiring: It's possible that there is a problem with the wiring between the door lock mechanism, the door lock sensor, and the control board. Check the wiring harness for any signs of damage or corrosion.
Check the control board: If everything else checks out, there may be an issue with the control board. Make sure that it is properly installed and connected. You may also want to try resetting the control board by unplugging the washer for a few minutes and then plugging it back in.
If none of these steps resolve the issue, it may be best to contact a professional appliance repair service for further diagnosis and repair.
