Kenmore Kitchen Ranges - Page 3 - Recent Questions, Troubleshooting & Support

If during the water heating step in the wash cycle, the water temperature sensor (NTC) value is out of range, or the heating element circuit has failed, the "F/05" error code will be displayed. Sept 5, 2015

Error code F 05 repair tips please. - Kenmore Elite HE3 ... - iFixit

and may also be the lid lock. https://www.justanswer.com/appliance/eqv65-kenmore-600s-washer-recently-started.html ..

Oven takes a long time to preheat: Igniter? - Hartford Courant How to Replace a Kenmore Gas Oven Igniter - Kenmore Gas Oven Takes a Long Time to Preheat - YouTube Oven Won't Heat: Troubleshooting Gas Range Problems - YouTube

no info generic answer glass seal failure repair/replace

It sounds like she has activated the self cleaning feature. Turn the power off at the breaker for an hour and that should reset it. That number is a Decal number regarding anti-tip. I was trying to find the manual for it. https://www.searspartsdirect.com/product/57c9bw76u0-0022-628/id-316221000 ..

Check for power. Check the element with a multimeter. Call for service.

That is classic signs of a faulty thermostat. Cheap enough to replace.

This is the only 880 that seems to be available https://www.manualslib.com/manual/503533/Kenmore-880-54202.html If it was available, it would be in this link https://www.google.com/search?q=kenmore+c880.6312091+manual ..

Hi Al I was hoping to find a parts schematic for that model, but couldn't find one. I checked to see if any government recalls but there are none. I found site with a comprehensive set of spares including the $380 control board, holy moly! I thought there might be a relay, but there doesn't appear to be. Unfortunately, it seems that your control board may have failed again. If you can partially strip it and trace where the clicking is coming from, and if it is on the control panel, you could replace the clicking part, which is suspect is an onboard relay. If you phone the company below, their techs might has some ideas. https://www.repairclinic.com/ProductDetail/608068 Best of luck with the fix, and for your continued recovery. A personal friend and pub customer of mine wrote a book called 'After Stroke', it is by David M Hinds. Highly recommended.

After Stroke: The Complete, Step-By-Step Blueprint for Getting ...

https://www.amazon.ca > After-Stroke-David-M-Hinds After Stroke: The Complete, Step-By-Step Blueprint for Getting Better: Hinds, David M.: 9780722538852: Books - Amazon.ca. and a review. He also has a small pyjama pocket size book called 'The Little Book of Recovery'. https://reedsy.com/discovery/book/after-stroke-david-m-hinds#review

The Little Book of Recovery by David M. Hinds - Goodreads

https://www.goodreads.com > book > show > 2812067-... The Little Book of Recovery book. Read reviews from world's largest community for readers. .. ..

There are places in the link https://www.google.com/search?q=oven+sensor+for+790+model+kenmore ..

Kenmore oven model 790 error code f1 The F1 error code in most of the Kenmore 790 models means the control is not sensing the temperature properly. The tech sheet advises us to disconnect power for 30 to 60 seconds, and after power is reapplied if F1 is still present, replace the EOC (Electronic Oven Control).Mar. 15, 2010

How do I fix an F1 error for my Kenmore 790 self-cleaning oven?

..

then set it for higher temp

This is the closest I can find https://www.amresupply.com/part/318115601-FRIG-RA-FUSE-HOLDER Aparently the model is a 'Capri C968'. Spares in the link, but many are discontinued. :>( https://www.google.com/search?q=Kenmore+capri+C968+parts ..

Could be control board failure

It is gas so you can't fix it yourself. You need a qualified service tech to look at it. The smell is normally caused by an incorrect mix of gas and air being burned and can be cause by spiders nesting in or near the gas jets.

Google 'make model spares' and look at the Sears website. Check all the components that control temperature control board thermostat control units sensor element (if it takes 'forever to preheat')

YES. The thermal fuse is a metal fuse that is located inside of a clear plastic tube on the left side of the inside of the control panel. (Source:https://www.apogeeweb.net/electron/what-is-a-thermal-fuse.html)

Check that the burners are clean. There is a small hole near where the spark electrode is and it often blocks. That hole directs a small jet of gas at the igniter electrode. Make sure the aluminum bezel below the burner is clean as it is part for the electrical circuit. Make sure the spark electrode hasn't moved away from the burner. Make sure the electrode wire is attached. You say it says propane, but it is on natural gas. I hope the jets conversion was done :>) It is a mighty fine stove, I am a chef!

That's not good. The self cleaning modes break more things than it fixes. Sounds like your has damaged the control panel logic board.

notify installer of problem new doesn't mean free from defects or improper instillation

https://www.appliancecodes.com/kenmore-range-f93-error-info-4-36/ be careful!!