Johnson Boating - Recent Questions, Troubleshooting & Support


Do you have a question?
If you are looking for the journalist Verity Johnson, start with her website http://www.verityjohnson.com/ or a Google search.

Johnson Boating | Answered on Nov 19, 2019


See this. At about 4 minutes, he shows where the bypass screw is located. The fuse could be an inline one and is probably located by the control switch for the tilt unit, but it may be located somewhere else, depends on who wired it up.

Johnson Boating | Answered on Nov 04, 2019


  • Anonymous Oct 30, 2019https://www.manualslib.com/manual/824998...
    Not sure if this helps.

  • Anonymous Nov 02, 2019
    Valve Clearance Specifications
    For motors 70-horsepower and above, set the intake at 0.005 mm and exhaust at 0.006 mm.

Johnson Boating | Answered on Nov 02, 2019


Great Work,
It is a nice Post. It was very helpful for me. Thanks
Keep it Up
<a href="https://tutuapp.buzz/">Tutuapp</a>
<a href="https://tutuapp.buzz/mobdro-apk-download/">Mobdro</a>
<a href="https://tutuapp.buzz/whatsapp-dp-latest-images/">WhatsApp dp</a>
<a href="https://tutuapp.buzz/instamp3-apk-download/">Instamp3</a>
<a href="https://tutuapp.buzz/mobilism-apk-download/">Mobilism</a>

Johnson Boating | Answered on Oct 25, 2019


ok so you have removed the propeller from the leg so now you need to get a spanner to fit the nut then turn the engine clockwise to undo the pinion gear

Johnson Boating | Answered on Oct 20, 2019


Hi ,check the needle and seat in the carburator it may not be not be cutting off the fuel when the carb is full as this can cause flooding into the throat of carb

Johnson Boating | Answered on Aug 25, 2019


You need to take off the carborator clean take apart clean with carb cleaner and put it back together good to go make sure the fuel line has no hole

Johnson Boating | Answered on Jul 18, 2019


remove the carbs and have them ultrasonically cleaned..use seafoam in your fuel

Johnson Boating | Answered on Jul 18, 2019


Normally they go to the console wiring harness. The tank has a low oil sensor in it . Has the system been by bypassed? When it is ,you have to add oil to to gas .

Johnson Boating | Answered on Jul 07, 2019


2005 close enough?

Page 40 says it is a dealer job!
http://www.operatorsguides.brp.com/OperatorsGuidesAttachments/OwnersManuals_EJ/attach/2005/5035765E.pdf

Videos

https://www.google.com/search?safe=off&rlz=1C1QJDB_enCA643CA644&ei=_FwaXcqpAsnSsAWdw7SQCQ&q=oil+filter+change+on+a+2003+Johnson+140+hp+outboard&oq=oil+filter+change+on+a+2003+Johnson+140+hp+outboard&gs_l=psy-ab.3...263459.269863..271822...0.0..0.107.746.6j2......0....1..gws-wiz.......0i71j33i10.Ip-HlB5NDP8

Johnson Boating | Answered on Jul 01, 2019


I think it is a 1990. See this model chart.
johnson-qj5ylfrn4mmd5ai1cp5ee0oi-2-0.jpg

Johnson Boating | Answered on Jun 25, 2019


18 to 20 ft lbs. Torque in 3 steps ending at the target ft lbs.

Johnson Boating | Answered on Jun 23, 2019

Not finding what you are looking for?
Johnson Logo

209 questions posted

Ask a Question

Usually answered in minutes!

Top Johnson Boating Experts

yungtek

Level 1 Expert

47 Answers

Brad Brown

Level 3 Expert

18121 Answers

NOEL
NOEL

Level 3 Expert

8537 Answers

Are you a Johnson Boating Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...