Jenn-Air Dishwashers - Popular Questions, Answers, Tips & Manuals

POSSIBLY CONTROL BOARD BUT WE CAN NOT GUARENTEE IT SINCE WE CAN NOT DO THE TESTING NEEDED

The accumulator filter is below the spray arm radiant shield, guard and wash impeller and above the wash motor and pump. See part 7 on the diagram: https://www.partselect.com/Models/JDB2150AWP/Manufacturer/1/Sections/PUMP-AND-MOTOR/?ModelID=89671&ModelNum=JDB2150AWP&mfgModelNum=&ManufactureID=1&Selected=55866&Position=2&mfg=Maytag&Type=Washer&Mark=2 . There is also an over-pressure filter on the dishwasher feed tube. See part 2 here: https://www.partselect.com/Models/JDB2150AWP/Manufacturer/1/Sections/WATER-DISTRIBUTION-ASSEMBLY/?ModelID=262050&ModelNum=JDB2150AWP&mfgModelNum=&ManufactureID=1&Selected=55865&Position=6&mfg=Maytag&Type=Washer&Mark=6 . I hope this helps. Cindy Wells

Contacts in manual may also help. http://kitchen.manualsonline.com/manuals/mfg/jennair/dw860.html

Sounds like a noisy circulation pump motor. As an Engineer, I would treat any abnormal noise seriously; the motor may require examination and possibly a new start capacitor fitting? or it may be loose or have a problem with its impeller, etc. Or it could possibly be a relay for the heating element is noisy. Either way, abnormal noises are unusual, and dishwashers need to be 100% reliable as they are often used unattended or overnight and any problem might indicate a possible fire risk. Sorry to be so heavy - is the machine subject to any guarantees or extended insurance etc? Some have 5 year guarantees. Whatever, I would call an engineer out to have it checked over.

The loud humming noise can be due to the pump sticking if a piece of debris gets trapped in it or an intermittent fault on the pump capacitor or starter relay. Check out these links below to get tutorials and advice on how to clean the pump or change the capacitor or relay which is cheap and simple job. How to replace Dishwasher pump Bosch Siemens etc Dishwasher Repair Manual Table of Contents http://www.ukwhitegoods.co.uk/help/fault-codes/dishwasher-fault-codes.html?start=25 I hope this helps

Can you hear the wash pump operating during the cycle? Pump could be faulty or blocked, or the pcb could be at fault

your washer has an electrical short most likely from water leaking on circuits most likely you need to replace the control panel on the uper door area unless the unit is leaking below

First check your circuit breaker to make sure it didn't trip, if that is good, turn it off and take the 2 mounting screws usually at top of the dishwasher going into the counter top and slide it out. Then check the connection where the line comes in and connects to the power on the dishwasher, they are usually connected with wire nuts. Make sure connection is good.

You broke it!!!!!!! Check out the wiring associated with on/off cycle. There might also be a switch by the door designed to not allow unit to turn on when door is open - check it out. It might not be engaged if the inner panel of door is not properly hitting the switch.

Try running bleach thru it... place a bowl in the bottom rack with bleach in it...start with a small amount... work up to what cures it.. The vent hose may have "crud" in it.. mine stopped up..D/W stopped draining..smelled..

repairs should be preformed by an authorized service person. the flat tube in the rear is a manifold that allows water to flow from the main motor assembly. if there isn't enough or any water flowing to the manifold then the manifold is disconnected from the main motor or the main motor is not pumping efficiently. replace the main pump assembly or reconnect the manifold to the pump if dis connected.

More then likely the washer control panel has failed.

If water still sprays around during a cycle, the pump works.

It sounds like your door latch got tripped into the closed position (even though your door is open). You MIGHT be able to use a screwdriver or some tool to be able to pull the latch lever back out to the open position, but it might also be necessary to take the door apart to get to the latch to be able to reset it. The real problem is that if it happened before, it will probably happen again. So the real solution is to replace the latch assembly. If you need further help, reach me via phone at https://www.6ya.com/expert/ronald_e6b9572cebe3ad27

it is usually the panel that fails

Whirlpool parts come with a one year warranty WP owns Jenn Air take it back I have replaced this panel then had to go back and change again in 3 days it failed yes could be a bad batch of panels the panel is powered by the control is the control taking out the panel can't say it is a computer maybe sending to high a voltage to panel no way to test that

Well, unfortunately, the last one I encountered like that, I had to replace the control board...

Unrelated, Jet dry is a surfactant to prevent water spots.

Specifically what lights are blinking? Do you have the child-lock (control-lock) turned on? If you need further help, reach me via phone at https://www.6ya.com/expert/ronald_e6b9572cebe3ad27

Free Jenn Air Dishwasher User Manuals ManualsOnline com