Jeep Logo

Jeep Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 628 Products
  • 222K Answers
  • 4M Views

You did not post where the leak is. You did not post what the problem is that caused the breakdown. You did not say how the vehicle was towed.

Jeep Cars &... | Answered Yesterday


go to local auto parts store and ask them to look at it. usually free at least here in usa

Jeep Cars &... | Answered 2 days ago


you have to get the new pcm programmed to that jeep...most independant mechanics can do it with a good scantool unit

Jeep Cars &... | Answered 3 days ago


could be a few things.
fuel filter , throttle position sensor, even a maf sensor could do that,
cherokees are known for bad ignition switches
try looking into the ignition under the key, you need 2 do is take it out look and see if corrosion or burn mark on copper connections or contacts it should take a T20 to take apart.

Jeep Cars &... | Answered on Jan 17, 2020


The 1996 Jeep Grand Cherokee Laredo Anti-Theft System is equipped with Vehicle Theft Security System (VTSS). VTSS system monitors vehicle doors, hood, liftgate and ignition. If an attempt is made to enter or operate vehicle without proper disarming of system, vehicle horn will sound, headlights, taillights and parking lights will flash, and engine will be prevented from running.

The following wiring diagram and electronics circuit contains detail schematics of The 1996 Jeep Grand Cherokee Laredo Anti-Theft System. Herein you will find interconnection between electronics parts of the system such as body control module, auto headlamp light sensor. VTSS led, driver door module, passenger door module, cylinder lock switch, junction block, power distribution center, and grounding. Herein you will learn also how the Vehicle Theft Security System works, removal, installation, testing and troubleshooting procedures.

Try HERE.

Also, remember that here can find the Jeep Grand Cherokee Service & Repair Manual.
Hope help with this.

1999 Jeep Grand... | Answered on Jan 17, 2020


Early bulb failure is caused by 1) high voltage or 2) bad ground connections, 3) excessive vibration, 4) corrosion inside the bulb connector

Jeep Cars &... | Answered on Jan 14, 2020


It doesn't use a relay , it's controlled electronically . The TIPM - totally integrated power module supply's B+ voltage directly to the headlamps . Your best bet , get a hold of the dealer . Recall on a lot of these TIPM'S .

Jeep Cars &... | Answered on Jan 14, 2020


maybe the socket is shorted to ground. you can replace it

Jeep Cars &... | Answered on Jan 13, 2020


Get your hands on a shop manual. We're not going to make a video for you.

2005 Jeep Grand... | Answered on Jan 11, 2020


the only grease fittings are on the upper ball studs thats it!!

Jeep Cars &... | Answered on Jan 10, 2020


you can not prevent the alarm from going off because there is no disarm switch in the door lock mechanism. the only actual solution is to replace the key

2005 Jeep Grand... | Answered on Jan 10, 2020


google the codes and find your links. or buy a service manual from a known source. not from some clown selling them here at fixya like derrick

Jeep Cars &... | Answered on Jan 08, 2020


borrow rent or buy a puller. you dont want to be hammering on that

Jeep Cars &... | Answered on Jan 07, 2020

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Popular Products

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14826 Answers

Brad Brown

Level 3 Expert

18157 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...