Intex Pool & Spa - Page 5 - Recent Questions, Troubleshooting & Support

Did u modify ur inlet/outlet hose? Wat did u use? Mine broke and I can't find one to order.

It might mean you need to clean out the filter or the chlorinator cell. I hope this helps.

What does the yellow light mean on my 8111

Hi I have a 637r pump that had no hoses when the pool was given to me so I was just gonna buy a 635t pump that has everything included for 50$ bucks can I use that pump in replace of a 637r pump?

Have your salt leavel tested to be sure it's not to low or to high.

? inconsistently - -or slow recovery its a very small and low kw heater in the unit takes a bit to recover -- make sure filters are clean and cover in place -- if heater not coming on and throwing codes problem with pump or heater the temp sensor is after pump and before heater -and or control head problem do and online search and will find hundreds of hits about the intex problems

There is a PRCD safety device that shuts the unit down if a fault electric current is detected. The device trips if water gets to locations that could cause electrocution. When it dries out it works and then stops when it gets wet. You need to check for air leaks using soapy water in a spray bottle.

Yes your kry board

there is no reset

En https://www.mahico.com/cerrajeros-barcelona/ trabajamos las 24 horas del d?a, los 365 d?as del a?o, ofrecemos servicios de emergencia de cerrajer?a que necesite. Si necesita abrir una puerta, cambiar una cerradura, abrir una caja fuerte de emergencia o necesita realizar un amaestramiento de llaves nos puede llamar de inmediato a la hora que sea. Nuestros servicios est?n garantizados, trabajamos para satisfacer a nuestros clientes y que queden felices con el resultado.

It means low salt level (below 2500 ppm). If E91 is shown do the following: 1) Test the salt level with a salt test kit. If a salt test kit is not available you can take a sample of the pool water to your local pool supply store.

I would suggest that you keep your salt level around 2,5 for chlorination, however to get the green pool sorted your pool needs to be shocked and would recommenced to get your pool's free chlorine level at least up to around 5 in order to shock the pool as normal free chlorine level should be 3

Hi my Intex hot tub spa is throwing an E90 code every time I try to turn on the filter and heating. What do I need to do to fix this?

A late answer but it might help future Intex impleller sufferers... they do not sell replacement parts and you won't find any impellers sold separately anywhere on the planet. I've had 1 Intex pool and 3 Intex filter pumps in 3 years. Last week the 3rd pump's impeller broke as well. I shan't buy their products again.

The E90 code on the Intex spa is due to a dirty water flow sensor. ... The black wire is plugged into a white wire, carefully unplug it and unscrew the sensor. Clean it good and blow out the hole it goes in. This will fix the code and you will be back in business https://www.justanswer.com/pool-and-spa/ap9qh-i-m-having-error-code-90-intex-hot-tub-intex.html

basically no use, unless you are setting it up and need to refer to a setting chart to insure it is reading in a specific range.

Use a brass rod 1/8" dia x 2 7/8" long. Plastic welding will not work as stated above. The original impeller shaft ceramic.

test gfi plug ---if its a spa most likely pump ceramic shaft broke How to repair Intex PureSpa pump E90 Error 90

Sorry we have no parts resources here.

I installed a new Intex ECO 8110 unit on my 15' above ground, steel sided pool. After about 10 hours of use I had the "code 92' high salt alert that shut the system down. I knew that my salinity wasn't high because the local Pinch A Penny pool store does free water analysis and i was given the okay just a week prior. We had also received a bit of rain in the interim so I knew that the alert was false. Here is how I fixed the problem (so far). 1. Turn your unit off. 2. Disconnect the power cord from the outlet and wait for 2 minutes. 3. Unscrew the retaining nut at the electro-cell connector and unplug the connection. 4. Rotate the plug 180 degrees to reverse the polarity of the plug and re-connect to the electro-cell. 5. Reconnect the power cord to your receptacle. 6. Turn the unit on, wait for the green light to burn steady. 7. Monitor for the next 5-10 minutes. My unit has worked flawlessly for 3 hours. If i receive another "code 92" alert i will repeat the procedure which will result in bringing the unit back to its original polarity.