Ingenico Computers & Internet - Page 9 - Recent Questions, Troubleshooting & Support
My ingenico i8550 not coming
Do you mean you can not switch terminal on?
If so you have to dismantle terminal and then to assembly it again.
You need IP6 screw driver to undo the main board.
To do this you need to know proper procedure for disassembly.
Aim is to disconect HSC module from main board clean the 120 pin contacts and put HSC back
in mating connector.
If you are not trained for this I suggest not to tamper with.
Kind regards Nebojsa
Trignometric problem
The answer is Square root of 2. (
)
They way it works is :
sec theta at 45 degre is 1 over cosine of theta or
cosine of theta is square root of 2 over 2.
Therefore you have 1 over square root of 2 over 2.
After rationalization and simplification you should have
.
BLURRY SCREEN
This problem is easily repaired. The heat seal connector between the PCB and glass is defective. For repair information contact
[email protected]
11/10/2008 8:30:21 PM •
Ingenico...
•
Answered
on Nov 10, 2008
I6550 configuration/initial install
You can find the user's manual at the URL below. From my experience, using this terminal requires active support from your POS software. It is said to work with Microsoft RMS, but I'm still trying to get mine to talk to the computer. Good luck with it.
www.ingenico.com/INGENICO_GALLERY_CONTENT/Documents/USA/products/multilane/DL00458_RevE_i6500.pdf
Pen writes in one spot, but image shows up 1/2 below.....
1. To calibrate the ENTouch 1000 power off the device.
2. Prior to restoring power touch the pen to the center of the screen and do not move it.
3. Power on the device. Leave pen in center of the screen and do not move it. If you move it the device will not enter calibration mode.
4. Allow device to boot. If you held the pen in place the EnTouch 1000 will enter calibration mode.
5. Follow the on screen instructions. Be very methodical and do not try to rush it...
8/8/2008 4:20:04 PM •
Ingenico...
•
Answered
on Aug 08, 2008
Dispaly on eN-Touch 1000 is getting blank
Check the power adapter, sometimes they get hot and they don't supply enough power to the pin pad. Also make sure that the power cable is not loose, twisted or broken, this can also contribute to the problem.
8/8/2008 4:16:21 PM •
Ingenico...
•
Answered
on Aug 08, 2008
What is digital marketing?
Digital marketing, or “online marketing,” is a form of advertising that uses the internet and digital technologies to connect with customers. Digital marketing seeks to accomplish the same thing as traditional marketing except by leveraging computers, smartphones, and other digital devices rather than traditional media, such as print, radio, or television.
Como cancelar el winter driver
EnglishIt is a car, and cars are complexbut no car was told , maker, model , and year.we can not guess cars. post the VIN? and all that is knownname a problem what can't your car do right?name symptoms or evidence that is confusing to you.then answers can happen.onlygood luck , finding itand Mucho Gusto.my guess now is this is posted to computer forumand not to CARS !must be some odd traction controls thing'but 10,000 models of cars,
I need a product key
Have you actually purchased Visio, or are you just trying to get it for free?
As a software guy, I would have to advise against piracy. :)
There are several ways to get Visio for cheap. If you are a student, there are discounted versions available online and in stores. Also, you can check with your school for even cheaper options sometimes. Try the university bookstore if available. Or a Computer Science department maybe.
If you are working, and your company uses MS Office applications, find out if they have the "Microsoft at Home" program. You can get MS Office applications for really cheap that way. I can get Visio through my company's "Microsoft at Home" program for a few dollars.
My Employer Says They Are Going To Cut My Wages. Can They?
If you are in the middle of a contract, then cutting your wages is almost certainly a violation of your employment law rights. While I am by no means an expert on this matter, I did have a similar issue years ago - mid-contract wage cuts - and I hired an
employment attorney to fight the case on my behalf. It turned out that my employer was basically looking to scare people into taking the wage cut.
They got into some pretty serious legal trouble for their transgression, and nothing happened to me in terms of wage cuts after that. If you are between contracts, your employer can re-negotiate your salary, but as far as I am aware, if you are in an agreed-upon contract, they cannot just decide to reduce your salary. If you want to settle matters, contest this action with support from a legal professional.
Solitaire master has a hang
clarify pi please. if you meant pi to mean main screen picture, you probably have used up your free time on this program.
Not finding what you are looking for?