HP InkJet - Popular Questions, Answers, Tips & Manuals

You may be using non original ink catridges, the printer chip will not recognise so flashes as if needs replacing.if refills are original printer chip may need to be reset.

Put the old ones back in and see if the error code goes away.

readjust the margins in the printer page set up just before printing

HP print heads are usually a part of the cartridge so when you get a new cartridge you have a new print head. However, they do have a models with separate print heads. If after installing a good ink supply and cleaning/aligning the works, performance is still unsatisfactory you may have no recourse other than to change the print head which can be expensive to the point where getting a new printer is more cost effective.

Insert the old cartridge, if the message goes away the new cartridges printed circuit is defective.

Printer Technical Support Phone Number 1-800-243-0019 for printer repair services & setup, install Dell, HP, Brother, Epson, Canon printer customer support.

The paper sense switch is not working. It's a little plastic tab that the paper pushes down when paper is loaded into the feeder.

You need to contact the rewards program at Office Max. Here is the link-

Test the wireless connection Print the wireless test report for information about the printer wireless connection. The wireless test report provides information about the printer status, hardware (MAC) address, and IP address. If the printer is connected to a network, the test report displays details about the network settings. To print the wireless test report 1. From the printer control panel, touch (Wireless), and then touch Settings. 2. Touch Print Reports 3. Touch Print Wireless Test Report.

follow the printer instructions in your manueal ur printer looks like 8600 pro or newer 8620,8630 I have no problems with my password I do have 8600 pro call hp they will walk u thru it complete

You need the accessory that permits two sided printing. Check HP web site for that part to make sure you have it and have it installed. Once installed, if you have the HP printer driver software installed and up to date for your computer operating system (PC or MAC), when you request a PRINT you will see PROPERIES button in the print dialog box. Tap that button and scroll down to TWO Sided Printing. That's it. This is a setting that will only stay active for the current print job. If you want the default to be two sided printing you can set that in the HP Solution Center under Printer Settings.

There's a chance that the pick up roller has a lot of paper dust on it. You can get cleaning paper from an office supply. It is sticky on both sides of the sheet. You run it through several times to clean all the rollers on the printer.

http://h10032.www1.hp.com/ctg/Manual/c04204791 try this Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

If you go to the screen on the printer and scroll through the options you can reset the printer to the factory settings. The screen is on the printer on the bottom right side as you face the front of the printer.

I hate to say it but good luck. HP makes very little available for the standard officejet products in terms of parts or manuals. They mostly treat these as return to HP for repair or if under warranty they do a exchange for a refurbished unit.

BECAUSE IT CANNOT FIND THE PROPER HARDWARE AND INK. TRY TO PRINT A TEST PAGE, AS WHEN YOU FIRST TEST IT.

All refill sets, come with a good description. But before you buy ink, make sure your cartridges can be filled and the chip can be reset. So you won't end with filled and unusable cartridges and dirty hands. Look here to see how things go: Ink Refill Kit For HP Officejet Pro 8610 8620 8630 8625 8615

buy new for,100, Amazon com HP Officejet Pro 8610 Wireless All in One Color Inkjet Printer... or,your manual, http://h10032.www1.hp.com/ctg/Manual/c04204791.pdf ,then call hp.

you can permanently change it printer properties.or when you are printing a page you can change the setting from black & white to color.