Hobart Welding Tools - Popular Questions, Answers, Tips & Manuals


Is it 220 vts ? If so, Check the outlet with a voltmeter to see if you have 110 vts. On both of the top terminals .

Hobart Welding... | 56 views | 0 helpful votes


It sounds like a relay is stuck closed. It could be on the control board. Call Miller welding and give them the model number and they will be able to help . Good luck

Hobart Welding... | 89 views | 0 helpful votes


Return it for another on or call Hobart customer service. Number is listed in the instructions that came with unit. Page 7-7
https://www.tractorsupply.com/static/sites/TSC/downloads/ProdContentPDFs/1021027_Man1.pdf

Hobart Welding... | 111 views | 0 helpful votes


It’s close enough not to be able to answer that. The inrush current of a welder is huge anyway, so it could exceed the instantaneous capacity of the generator. However, it’s also possible with capacitance in the welder to smooth that out, that it will work fine. The only way to be sure is to test it. If you can’t do that before purchasing, it’s a risk you take. On balance it should work, but may not.

Hobart Welding... | 95 views | 0 helpful votes


Request the wiring diagram (not schematic) directly from Hobart.

Hobart Welding... | 168 views | 0 helpful votes


MIGHT JUST BE YOU ARE OVERWORKING IT . THEY ARE NOT MADE TO RUN FOR LONG PERIODS OF TIME CONTINUAL

Hobart Welding... | 203 views | 0 helpful votes


Lots of torches are fairly universal and you are likely to find it cheaper to replace only the parts needed if you can find them - manufacturers tend to prefer to sell the torch (or gun) complete with the hose, cables and sheath and they are expensive though considerable savings can be made dealing with factors or independent supplier/repairers.

Most professional mig welders over here use the euro torch and when a welder doesn't have one and the torch is ready for replacing it is a worthwhile modification, especially if the necessary parts can be sourced secondhand or salvaged.
The euro torch just plugs into the machine and once the machine has been modified there are plenty of usable secondhand ones about that can be had for a song.

If you aren't conversant with the euro torch, try a search...

Hobart Welding... | 449 views | 1 helpful votes


Request the manual from Hobart.

Hobart Welding... | 407 views | 0 helpful votes


take it in for a check of the relay for the wire that turns on the power when the trigger is pressed
that relay activates the gas solenoid and the power to weld

Hobart Welding... | 306 views | 1 helpful votes


Hey Joe, Sounds like a fuel starvation issue... the needle/seat/float that controls the flow of gas into the carburetor is probably sticking and letting a TINY amount of fuel in the carb,, running the engine burns it dry too quick and quits... takes a few minutes for it to refill, then you start it, and run it dry again,, (repeat-repeat-repeat).. sound about right?? Take it to any GOOD small engine mechanic... they can clean and set the carburetor...
this is no biggie.. just very aggravating..
Good luck! .please mark as helpful...

Hobart Welding... | 833 views | 1 helpful votes


You are probably going to have to replace the complete assembly, and it is probably going to cost about $150. I would contact Hobart by phone with your serial #, and they should have the correct part# , since there is no parts list in your manual, and none seem to be available on line. BRwelders has part# 210010 listed but may not be correct, since it is for the 120.

http://www.brwelder.com/kit-feed-mot...er-120-210010/

Hobart Welding... | 1,169 views | 0 helpful votes


Not really.
You can purchase aluminum stick electrodes, but they generally don't work that well.
You will find it best just for steel.

Hobart Welding... | 586 views | 0 helpful votes


Any welding supply store should be able to get you one. It comes from Miller.

Hobart Welding... | 1,242 views | 0 helpful votes

Not finding what you are looking for?
Hobart Logo

460 questions posted

Ask a Question

Usually answered in minutes!

Top Hobart Welding Tools Experts

David Soto
David Soto

Level 2 Expert

414 Answers

oneStan
oneStan

Level 3 Expert

434 Answers

John Ziehm
John Ziehm

Level 2 Expert

206 Answers

Are you a Hobart Welding Tool Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...