GE SpaceMaker - Recent Questions, Troubleshooting & Support - Page 7


not possible sorry

GE SpaceMaker... | Answered on Feb 10, 2016


I'd check to see if the turntable motor has continuity. If it does, check to see if 120 volts is being supplied to it. If both are o.k., then the motor has probably bound-up in some way internally. There's also the possibility that it has mechanically become detached from the hub that turns the glass tray.

If you need further help, I’m available over the phone at https://www.6ya.com/expert/david_29ad5d1dd86564b0

GE Spacemaker... | Answered on Feb 08, 2016


The first thing I would suggest is a hard reset. Unplug the unit for a minute or so. Then plug it back in, set the clock and try again.

If that doesn't work, leave it unplugged for about 5 minutes.

GE Spacemaker... | Answered on Feb 06, 2016


It may be damaged from inside. Check it to the Oven Specialist. He will assist you and told you that what's wrong.
Maybe its Power Problems that causing heat not to produce.

GE SpaceMaker... | Answered on Feb 03, 2016


hi..it sounds like a magnetron problem.It might have
got into damage.
check this out..
thank u..
kindly rate my response..

GE Spacemaker... | Answered on Jan 31, 2016


i need the model number pls in order to help you

GE Spacemaker... | Answered on Jan 10, 2016


There was a component failure in the magnetron circuit. The magnetron is the device which produces the microwaves that heat the food. There are extremely high (and dangerous) voltages associated with this part of your oven. As a result, components often fail and make noise because these components can burst rather violently. You should take it to a competent service tech. The components associated with the magnetron can often be replaced when they fail and it is not always expensive to have repaired.

GE Profile... | Answered on Jan 04, 2016


the vent tube in back may not have been changed over they can be vented or ventless but you must switch the flap in back you had the answer in your question ... good job,,..lol

GE Spacemaker... | Answered on Dec 22, 2015


You're going to have to replace the keypad module and possible the control module (do the keypad first). You can try contacting these folks: http://www.appliancepartspros.com/search.aspx?model=jem31sa%20001%20ge%20spacemaker%20microwave
And see if they have a keypad for your unit. Depending on the age of your microwave, you may be best off replacing the whole microwave.

GE Spacemaker... | Answered on Dec 12, 2015


I would say replace it . but a repair shop will give you an estimate then you can decide if it is worth the cost of repairs .

GE Profile... | Answered on Dec 10, 2015


Well the only way to fix it, replace the keypad control board, but consider the cost in parts, it will rival some new microwave ovens.

GE Spacemaker... | Answered on Dec 08, 2015


Good afternoon Penny.

The manual for this microwave can be obtained/viewed here ( and have tips for all those other things like changing the scroll speed of the display )
http://products.geappliances.com/MarketingObjectRetrieval/Dispatcher?RequestType=PDF&Name=49-40536-1.pdf

If you go to to Page 24, the time set is a fairly common one:
  1. Press [Clock]
  2. Enter Time of Day with numeric keypad
  3. Press the [AM/PM/Scroll Speed] Button under the Zero key.
  4. Push [Clock] or [Start] to finish and set the time.
Cheers - hope this helps.
D

GE Spacemaker... | Answered on Dec 01, 2015


two screws in the floor of the cabinet/space above it ?

GE Profile... | Answered on Nov 30, 2015


probably a magnatron failure
take it to an appliance repair shop for a proper diagnosis and get a quote as repairs can be more expensive than new unit

GE SpaceMaker... | Answered on Nov 24, 2015


The part of the oven called the "magnetron" (this part is what creates/generates the microwave energy that heats the food or liquid) is burned out, the cost to repair is more this part is more than the cost to replace with the cost of Microwaves so depressed by the stagnant economy.

GE Spacemaker... | Answered on Nov 24, 2015


The error code F3 indicates an oven sensor problem. The oven sensor is most likely the failed part. The oven sensor probe must have the correct resistance readings at specific temperatures. When the electronic range control (ERC) cannot identify the correct resistance of the oven sensor or the resistance is way out of specs F3 will display.
I recommend calling a service technician to diagnose and repair your oven.

GE Spacemaker... | Answered on Nov 20, 2015


microwave is in lock mode. How do you unlock to use?

GE Spacemaker... | Answered on Nov 18, 2015


If you pull the covers, you will see a digram showing locations of overheat safety sensors. Check with a meter. If all good. You have other issues.

GE Profile... | Answered on Nov 11, 2015

Not finding what you are looking for?

-1,212 questions posted

Ask a Question

Usually answered in minutes!

Top GE Microwave Ovens Experts

Poppa Maddo
Poppa Maddo

Level 2 Expert

372 Answers

William Miller
William Miller

Level 3 Expert

9179 Answers

Jimmy

Level 2 Expert

61 Answers

Are you a GE Microwave Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

GE Microwave Ovens

  • Forum

View Most Popular

  • GE Microwave Ovens
Loading...