GE Home Security - Popular Questions, Answers, Tips & Manuals
Motion detector is not working for GE INTERLOGICX 60-806-95R
All wireless security motions have a 3 min delay built into them. This means that whether the alarm is set or not when the motion detector picks up motion it shuts down for 3 min and will not pick up motion. This is done to conserve battery power. So I always advise customers to arm the system and stay away from the motion for 3 min total. example: 60 sec to arm system + 2min wait time. then try to trigger motion. If this does not help and assuming batteries are good, you'll need to replace motion. Good luck. This may help https://al.ly/vR54zP
Simon xt key fob
doors and windows are armed with the single press. All devices programmed as "perimeter" will arm. "interior" devices still need a second press of the lock button
I keep getting a false allarm from one of my
Double check the alignment of the sensor and magnet, the house may have settled and the alignment may have changed enough to show the fault / set the alarm off. There should be a notch or series of notches on the transmitter, make sure the magnet is centered on that. Also make sure the gap between the two is as small as you get it and still able to operate the windows (both vertically and horizontally). If all that checks out, you could have a tamper switch (GE uses a spring to hold it down) that is not getting fully depressed. or, you may have a bad transmitter. If it is the spring, you may be able to stretch it out a little to ensure good pressure on the tamper switch.
I can log into my system using ie 7 and windows xp
Try removing the plugin and reinstall if it is there. It is possible the plugin did not install properly or it was blocked by security settings. You may have to lower security settings temporarily while you install and may have to enable active x settings.
Ds 924 motion detector
It may have been previously learned into a zone. Sometimes, the motion will trip and activate a signal that can be learned into another zone you are trying to program. exit programming, then "tamper" the cover for the circuit board, not the battery access, on the motion, check the "status" light to see if a zone is displaying "tamper". Also check battery orientation in back of motion. When battery is first installed correctly. The light should activate during the first minute.
GE RANDOM VACATION TIMER GE5111N-71D also known as GE5111N
VERY straight forward setup. SET the Dial to the correct
DAY of the week and
TIME. This timer is
PRESET at the factory and you can
NOT adjust
any other ON/OFF settings yourself!
"Pre-Set" mostly for
evening and later evening times or hours "ON/OFF".
These times CHANGE from evening to evening and again,
ALL settings are made by GE! ALL ON/OFF cycles change from evening-to-evening and day-to-day.
120VAC operation.
SWITCHES: 1,875 WATTS MAXIMUM!
1,250 WATTS if you connect INCANDESCENT LAMPS!
I hunted and hunted for the specs on this Timer, but found none. I finally purchased two and read the tiny manual. I set one up in the kitchen to TEST with a 50 Watt lamp and it works GREAT... I just don't know WHEN it will cycle next, but I guess that's the mission and point of these spiffy timers!
SOGLAD
I recently installed a GE
Check the outlet to ensure it :1- has power , 2- is not a switched outlet. Check your wire connections to ensure they are secure. If all of the above are good, the transformer may have shorted when disconnecting. Use a voltage meter on the transformer terminals and the AC scale, check the output of the transformer.
Low battery and Phone communication failure
Check that you are not using an app that is continuously accessing the internet and communicating with a server for some reason that is using the phones WiFi or mobile channel. This will drain battery life if incorrectly configured etc ( i.e selecting access to your location, services and other info )
I have alot of CyberDome ll cameras (probably 30)
Most likely capacitors failing on the camera process board. They can also cause no picture, dark picture and sync loss. I use freeze spray to try to make the symptoms happen and heat to bring try to isolate it to an area. It's not so easy to change the capacitors if you do find which one (s) though.
Not finding what you are looking for?