Frigidaire Kitchen Ranges - Page 3 - Recent Questions, Troubleshooting & Support
My oven is beeping F11. (i unplugged the oven
Hi,
The
F10 F11 F12 F13 F14 Error Codes indicate that the electronic oven
control board senses a runaway temperature condition in the oven through
the oven sensor circuit.
This can be caused by a faulty oven temperature sensor probe or a failed electronic control board.
Oven temperature is detected by the control board as it monitors the resistance through the oven temperature sensor circuit.
You
could have a failed oven temperature sensor, a wiring harness failure,
an open thermal switch or a failed electronic oven control board that
would cause this problem.
The first component to check would normally be the oven temperature sensor probe.
If
you have a volt/ohm meter, you can shut off the breaker for the range
and remove the screws that mount this sensor to the back wall of the
oven.
Carefully pull the wire harness into the oven cavity until you get to the wire harness disconnect plug.
You should have enough slack to pull it this far into the oven.
Disconnect
the sensor but do not let the wire harness retract back through the
back wall of the oven or it will be hard to reconnect.
Measure the
resistance of the oven temperature sensor with your volt/ohm meter. At
room temperature, the resistance should measure around 1100 ohms.
The resistance chart is shown in the image below.
If
the resistance is above 2200 ohms at room temperature, then the sensor
probe is causing the F10 error code and will need to be replaced.
You can order a new sensor probe from the Sears PartsDirect website. The part number for the sensor is 316217002.
If the resistance is normal, then one of the other causes mentioned above is producing your F10 code.
You
would need to access the electronic oven control board (Timer) in the
console and check the resistance at the sensor circuit connection to the
control board as the next step in troubleshooting this problem.
http://media.fotki.com/1_p,wbqdsfkrfqtswfqxgtqsskgwtqkq,vi/krdbrtqkgxkrbbqbrwb/1/1303472/5961857/image37801img-or.jpg
Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.
Thanks to blueextc3221 for this solution.
Frigidaire oven FSC88B-4 shows "Err F3 " message. What to do?
F3 - Open/shorted sensor (RTD probe) connection.
Check the temperature sensor and the wires and plugs between the sensor and the EOC are good, replace the temperature sensor (RTD probe). If the sensor and wiring are good, the EOC would need to be replaced.
Dim Digital Display
Connie P,
Unfortunately it is not possible to make the display brighter. The only solution is to replace the entire clock/timer. The price for the part is less then a hundred dollars and if you will give me the complete model number and a color, I can help you to find the best deal.
Gendos...post back
Replaced element, oven is still not heating
You may still have a bad Electronic Range Control (ERC). This is your timer that you mentioned. The oven is controlled by the ERC. There is a separate circuit for the BROIL and BAKE functions. Does the BROIL element still work? Or, are both elements not working? You may want to double check all your connections from the element to the control board as well. Sometimes the wire lugs can oxidize and not make good contact. Check the ERC to see if there any obvious signs of failure. Burned components are common. These boards are considered "non-serviceable" and usually requires replacing. You can attempt component-level troubleshooting if you are savvy with electronics. There's usually a basic block diagram that comes with your appliance mounted somewhere inside the operator console or on the back panel of the range.
The ERC for your range would cost in the neighborhood of about $100 - $140 to replace. Prices will vary between model versions and will also depend on where you get it. It is a very simple repair job if you wish to pursue this yourself. I can give you step-by-step instructions if you need further assistance. I hope this helps you.
PS The reason all your surface elements still work is because they are controlled by infinite switches behind the control knobs. There is a separate switch for EACH burner.
12/23/2019 10:29:04 PM •
Frigidaire...
•
Answered
on Dec 23, 2019
Not finding what you are looking for?