Fisher and Paykel Washing Machines - Page 6 - Recent Questions, Troubleshooting & Support

It could be your main bearing going bad

I got this free Pdf manual from an online store for free and I don't think Ive visited a mechanic or fixya for help for more than 3-4 times out of the all the times I fixed the chipper in these 4 years

I would suggest finding YouTube video for your specific model.

not on this portion of the site go to the fridges in the home page eric

blown fuse on the main board

Error code 136 motor stall. Can be caused by several things. 1. Faulty wiring or copper stator in motor. Check with ohm meter. You haven't said what model so I can't tell you what your ohms should be. 2. Faulty RPS (rotor position sender) That little circuit board on top of the stator. You need a special RPS test meter to check it. 3. Drum seizing up. Try spinning the steel bowl by hand, it should be very easy to rotate and no loud bearing noise. 4. Faulty main control board. Don't worry about the cracks in the stator. Nearly every machine I work on has cracks. It doesn't affect performance.

possible board fault if rps has already been replaced,also check lid switch isnt faulty

check breaker

did you check breaker

I think they have a section with all error codes on their website https://producthelp.fisherpaykel.com/nz/Troubleshooting/Fault_Codes Good luck.

Hi just read your posting.Error code 43 is called OUT OF BALANCE SWITCH ERROR.This means either your switch is faulty or your your control module is faulty.95 % of the time it is your switch which is located under the control module which is under the top panel.If you want I can guide you step by step in the replacement of this switch.Please reply on how you would like to proceed and I will help you as much as I can.Looking forward to your reply.

I also got Error Code 37 at the end of a wash with the machine full of suds. I used the other information listed under this problem to establish that the pump was blocked, (no amount of hand-turning loosened the fan). After unplugging the machine from the wall, I removed the pump easily by unplugging the power and earth from the pump, pressed in a clip on the side of the pump to allow the whole pump to rotate and then pull out, (a bayonet type fitting). From where the pump came out from was a small piece of cloth and other gunk! I refitted the pump and reconnected the power and earth. The machine is now working happily again.

check drain pump is not blocked or faulty

Your Error code is 130 130. (10000010) Phase 1 to 6 Single Rotor Position Sensor Error The Motor Controller has found an error in the pattern received from the Rotor Position Sensor. Likely causes of this fault are a bad connection on the harness between the Rotor Position Sensor and the Motor Controller, or a faulty Rotor Position Sensor. Primary Source: Wiring. Action: 1) Check for corrosion on the edge connector of the Rotor Position Sensor and the Motor Controller module connector. 2) Check the contacts on the rotor positional sensor end of the hall harness to see if any have been damaged. (Each set of contacts in the socket has two wipers. If the distance between these wipers varies between different contacts, replace the rotor positional sensor harness). Secondary Source: Rotor Position Sensor. Action: Check the Rotor Position Sensor with an R.P.S. tester. Replace if faulty. Tertiary Source: Motor Controller module. Action: Replace Motor Controller module.

Check your lid switch. Take a PLASTIC Knife while lid is open and settings are on wash cycle...Stick it in the lid hole then see if washer turns on ..It might be cracked..That wound be the reason some time it works... Sometimes it don't...

Not enough details. What is the model number and how did you come up with error code 34. That code only applies to a very old model ( over 20 yrs old) While it is beeping do not press ant buttons and write down which lights are on along the top row. Count from the left and tell us which number lights are on and which are off.

I own and have repaired my smart drive washer. The water pump is very simple to remove on these machines. Unplug the machine and drain as much water from it as possible. There's a small plastic locking tab on one side of the pump. Gently pry it away from the body of the pump and twist the housing until it comes free from the metal pump housing anchor plate. Unplug the pump from it's connection and remove it. Found a guide that should help you - How to Drain Washing Machine That Won Empty Cares Appliances

Check drain pump for operation or obstructions