Fisher and Paykel Washing Machines - Page 5 - Recent Questions, Troubleshooting & Support


RPS (Rotor position sender) fault. The RPS is an electronic sender unit mounted on top of the motor winding. It tells the main control board what position motor is at for it to start properly and also if motor is actually running. Replace the RPS.

Fisher and... | Answered on Jul 09, 2018


The fuse is built onto the control board. It is not designed to be replaced. My 3 year old machine lost the water pump and blew the fuse. About $375 to fix. I am buying the new pump and will attempt to replace the fuse on the board. I hope there are no other bad components.

Fisher and... | Answered on Jun 28, 2018


usually means it need a repair or service,check the drain pump is ok and not blocked or jammed also when empty push down on the centre of the bowl it shouls have a good resistence to being pushed down if its really soft then replace suspension rods

Fisher and... | Answered on Jun 04, 2018


maybe it could be the board is not crrectly in place so look at that first

Fisher and... | Answered on Jun 01, 2018


faulty pump or blown board

Fisher and... | Answered on Jun 01, 2018


perhaps the pump is bad .

Fisher and... | Answered on May 31, 2018


You need to be more specific. There are 5 wash lights and two rinse lights. Each have a different number value when working out the error code. Count from left and say what number light is on. Spin being the 8th light from the left.

Fisher and... | Answered on May 18, 2018


Error code 40
40. (00101000) Inner Basket Disengage Fault
While carrying out a basket check, the Motor Control Module has found that the basket is
not engaged even though the pressure sensor indicates that the tub is empty. The Motor
Control Module continues to check for 2 minutes, after which time it displays this fault. The
first two areas to check are the clutch and the pressure tube. If these two appear correct,
then the fault could be in the pressure sensor in the Motor Control Module.
Primary Source: Mechanical.
Action: 1) Check that there are no clothes or other foreign objects preventing
the clutch from re-engaging. Excessive suds can stop the basket
rotating.
2) If the machine is empty of water, carry out a clutch disassembly
procedure (Refer to section8.14) and check the spline drive.
3) Next check that the pressure tube has not come off and that it is
not kinked.
Secondary Source: Motor Control Module.
Action: Replace Motor Control Module.

8.14 Removal of Clutch Mechanism (Spline Drive / Spline
Driven)
(a) Follow the procedure for removal of Inner
Basket. (Refer to Section 8.13).
(b) Remove the 3 screws securing the spline
driven to the inner basket.
Reassembly:
Refit in the reverse manner. Ensure that the
screws are tightened sufficiently with out over
tightening.


clipboard01-qpfuxc3flbegemdt4bpus14r-4-0.jpg

Fisher and... | Answered on May 13, 2018


Blockage in drain pump. You will have to empty water out with a jug. Then get machine outside and remove drain pump so last of water comes out. Check for any rubbish in pump, then put pump back and test it.

Fisher and... | Answered on May 12, 2018


Sometimes things can get out of sync. Try unplugging the machine for a few hours to rest the code on the board.

Fisher and... | Answered on May 10, 2018


15.5 Size Setting
If a new motor control module is fitted, the size switch settings will have to be set in the memory.
To size set a L.C.D AquaSmartâ„¢ machine:
1. Press and hold the left SCROLL button, then press the HIGH EFFICIENCY button until two
beeps are heard.
2. Press the SCROLL button to select the machine size (600 for WL70, 650 for WL80).
3. Press the POWER button.

Fisher and... | Answered on May 06, 2018


All replaced electronic boards need resizing.
Going by your post your have an AquaSmart machine
Here are some details to resize an AquaSmart machine

24903416-ei0rt0v231vo43kgyqwiblfx-4-1.jpg

Fisher and... | Answered on May 02, 2018


removing bowl is the best way

Fisher and... | Answered on Apr 21, 2018


you can buy lint filters from f&p but your main problem is caused by something like a tissue or something like that disintergrating inside ur machine best thing to do is remove inner bowl and thougherly clean both

Fisher and... | Answered on Apr 21, 2018

Not finding what you are looking for?
Fisher and Paykel Logo

4,179 questions posted

Ask a Question

Usually answered in minutes!

Top Fisher and Paykel Washing Machines Experts

Archie Ferrarini
Archie Ferrarini

Level 3 Expert

869 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a Fisher and Paykel Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...