Evenflo Aura - Popular Questions, Answers, Tips & Manuals

Kindly follow the steps below to fold the stroller:
• Use the ball of your foot to push down on the brake lever, located near the rear wheels of the stroller. Gently push on the stroller to confirm that the brakes are set. Grip the front edge of the stroller's canopy, if present; pull the canopy back towards the rear of the stroller.
• Push the tabs securing the ends of the harness straps to the harness buckle. Pull the straps aside and remove the child from the stroller.
• Kneel down next to the stroller's front wheels. Locate the locking mechanism set in between both pairs of front wheels. Use the locking mechanism to disable the swivel feature on the front wheels.
• Pull the stroller's seat back down to the lowest position; some models may feature locking mechanisms located on the sides of the stroller or built into the handlebar. Lift any latches securing the sides of the stroller in place.
• Push the handles of the stroller downward. Push the rear section towards the front of the stroller until the device is fully folded. Clip the storage latch located on the side of the stroller to the side of the handlebar.

Hi Danielle We would recommend you contact Evenflo for assistance. Contact Us

Hi Fumbling

You can try this Link, it will lead you to a .pdf manual to save/print/read.
Explanation about washing/detaching and attaching the fabric on page 9 "removing the seat pad".

Hope this will help you out!

Kind regards

Why not replace both rear wheels with 2 wheels from another stroller (not necessarily the same model as yours). I bet you could find something that will fit in, regardless it is the same model or not.

hi here is evenflo recall list I cannot find the aura on it

http://safety.evenflo.com/cs/sc/cssc_RD.phtml

On the back of the seat (under the handle) there shuold be a little plastic lever, if you pull that up it should lie the seat down, and to raise it you just pull the lever again and push the seat up,
Hope this helps

You can purchase replacement parts for your Evenflo Aura Traditions Travel System here: https://plweb.evenflo.com/replacement_parts.aspx

Just type in your Model number, date of manufacture, and press search. Find the part that broke and purchase it. Thank you for choosing Fixya.com! I’m happy to help further over the phone at https://www.6ya.com/expert/jeremy_69f3cc28d95bf514

Sounds like it somehow got overloaded. Did anyone step on them? Single strollers are typically tested to hold up to 100 pounds, which is well above the weight of a child and their gear. Regardless of what happened, contact Evenflo directy and see if they will replace the rear axle and wheels. You can't by replacment wheels at any store.

If you call Evenflo customer service they will normally send one to you at no charge.

mcdevito75 here, Contact Even flo aura at 800-233=5921 8A----5P EST. Hope this helps.

I am looking for the back wheels can you help me please the model number is 1621854A.

please look for an I shaped adjustment loop -= slide it to adjust and you are done.

Look for an I shaped adjustment band and move it to adjust the car seat belt.

Make sure that nothing on the bottom (near foot rest) is holding the stroller up from opening.

This is usually what happens.

Please let me know if you need further assistance.

carsandcomps,

Guru, Premium Expert @ Fixya.com

Those go a certain way and no other. For future reference the way to remove the belts is to release the metal oval under the seat and bring it up thru the holes in the bottom of te seat, then out thru the back. You have to undo the clasp and chest snap. Now....you have quite a problem as the straps are responsible for saving a life in the event of a motor vehicle accident. This being said you can try and slip the doubled over ends thru the end that is most narrow, slides into the track and the wider part snaps over the keeper on the seat itself, a little snapping plastic button. Next it goes under the lockdown and up into the first hole. You will need to compress the adjuster of the locking mechanism to get it up thru. If you can do this the next step is down thru and out the end of the locking mechanism. If the holes are too bound up and wont let the end of the belt thru, you may need to cut off the very end and re-thread it, then fold over the material and resew the end over itself to reform the stop. Cutting a belt is a last resort so make sure you are careful and that it is working properly. Otherwise, go buy a new seat. Good luck

just look for the manual online and use it congratulations

There should be small levers just beside the tires on the inner edge. These should be in the up position to be unlocked.
Hope this helps.

Try www.evenflo.com and use Contact us at bottom left. Request a manaul via email. You will need Model # and Serial Number and Date of Manufacture (MFG). Be sure to see if yours is part of their recall for the embrace car seat.

contact www.buggypitstop.co.uk they repair and service pushchairs and car seats