Emerson Pool & Spa - Recent Questions, Troubleshooting & Support
MY EMERSON POOL MOTOR MODEL K63CXERL-4778 BURNED OUT. WHERE CAN I GET A NEW ONE?
Is the front of the motor where it connects to the pump round or squared with "ears " at the corners where the bolts are? Also, it is a 1HP correct?
If it's round, any 56J c-flange motor will work and if it's squared, a 56Y is the replacement. I order most of my replacement motors from Poolsupplyunlimited.com because they have great pricing and additional warranties that cover far past the manufacturers 1 year warranty.
Emerson Hi-efficiency1081Pool mtr.EUSQ 1202 mod T55CXCJK-1345 for sprinkler 2.0 hp. Blown internal seal
the seals are replaceable/ the motor is a C faced motor it is quite possible water got into motor. Mechanical seals should not be replaced by homeowners, they want to to touch seal faces and this will destroy seal. Look locally for business that install water pumps and let them handle it. The motor will need to be rebuilt so check price and compare to new motor around $250. If the rebuild is half or greater replace with complete new unit.
How to replace pump seal on hot tub with emerson 1081 motor and gasket replacement on 2 inch
Emerson is the motor manufacturer. 1081 is the swimming pool duty motor designation. In other words all pool pump motor manufacturers have a 1081 motor. The mechanical shaft seal is going to be a part of the actual Pool pump itself. The seal is between the seal plate and the impeller. If motor is extremely noisy, then the leak allowed water to get into bearings and cause damage. If the motor is really noisy, or the shaft doesnt spin freely, then you may have damaged motor bearings. The pump manufacturer can usually be identified by markings on parts of pump ( in front of motor ).
Where can I find a diagram to fix a pump K55MYGRD-8367
this can be a hard pump to service. but you can remove the front pump housing and see if you can remove the impeller by hand, the back of the motor will have a screwdriver slot in the shaft to hold the rotor still while attempting to unscrew the impeller. after removing impeller you will need to remove the 4 thru bolts this will allow you access to the ceramic portion of the shaft seal assembly.
replace all needed parts and reassemble. never run pumps dry always prime the pump with water.
doing this job can save you a bunch of money and usually cost about $150 at my shop.
Jay the pool pump repair guy Longwood FL.
I am trying to wire
You really need a 2-pole timer -- 2 wires in and 2 out. In that case the Black/White from the receptacle goes to the 2 "in" terminals and the 2 red wires from the pump go to the 2 "out" terminals. The WHITE wire from the receptacle goes nowhere - tape it off. The Bare wire from the receptacle goes to the GREEN (ground) wire on the pump.
A single-pole timer can be used, but in that case, you ALWAYS have 110 v on one side of the pump. Not safe, and not code compliant.
How hard is it to change the motor out in an Emerson pool pump model k63cxese4793
(Challenger Pyrex triton)
NOT tat bad, (first x2) shut breaker off next take off the stainless steel band, pull motor and seal plate back from plumbing portion use wrench on back of the shaft of the motor, impeller screws off to the left, take out 4 9/16 bolts that attach the motor to the seal plate, give seal plate a tug and it should separate from the motor. use new seals especially the shaft seal (the one w/the spring in it) and put it back together. tap on the SS band this allows it to evenly pull up around the tank body lastly FILL PUMP (prime) with water.
or search for your LOCAL POOL PUMP MOTOR REPAIR GUY. and ask about installing the motor on the seal plate.
I charge $20 and it includes the shaft seal (most pumps)
Replace water pump
fix it, but the longer you let it run the more damage done, search your area for your local pool pump repair guy with free testing,
some of these pumps can be CRAZY expensive NEW but cheap to fix/rebuild/repair/bearings.OR a suitable replacement motor might be avalibl FYI
Emerson 1081 pool pump is working but running
fix it, but the longer you let it run the more damage done, search your area for your local pool pump repair guy with free testing,
some of these pumps can be CRAZY expensive NEW but cheap to fix/rebuild/repair/bearings. FYI
Hello,
I have an Emerson Spa
should be a 30, you can have the old one tested it might be good ? I write the value on the back and side for future reference to avoid this problem as the value is normally not stated on the motor's label like is done on air conditioning motors. search your area for your LOCAL POOL PUMP MOTOR REPAIR GUY WITH FREE TESTING
Emerson pool pump model k63cxesf-4793
Emerson is the manufacturer of the actual motor, not the entire pump. Many manufacturers use Emerson motors as a base for their pump systems,
You need to contact Emerson Motors USA for warranty info. Please have the "sticker" info on the pump motor available.
What causes a pool pump motor to overheat
Blocked or clogged water input line
Sucking air from a leak, not enough water thru system
Excessive debris in strainer baskets
Filter needs to be backwashed
Filter needs new sand or new cartridge
Filter needs to be taken apart and "fingers" cleaned
Filter Pump Impeller is obstructed
Filter motor is in-correctly wired
Filter motor bushings need replacement
Filter motor bearings are worn
Filter motor is "shot"
Not finding what you are looking for?