eMachines Computers & Internet - Page 4 - Recent Questions, Troubleshooting & Support

would not recommend it but if the tower is very sturdy and doesn't have a flimsy cover it should hold the wait of the monitor without any problem just make sure not to set the monitor on the side where the mother board is because it may damage it if any kind of flexing is done in that area

Your best bet is call a tech to remove them or order a restore disk on ebay. If you tell me the name of the program that is popping up I may be able to point you in the direction of removing it. You can try a program called Malwarebytes go to there website and download the software do the 14 day trial and run the scan see if that will remove it if not you will have to do other more technical actions

Try changing the browser you are using. Also make sure both the browser and Adobe Flash Payer are updated to the latest version.

Try unplugging from power source and leaving for about three minutes and then plug it back in.

tryed safe mode f5 or f8 last known good

Disconnect the power cable open the case and pull the CR 2032 battery out for a minute. That will reset the BIOS. If you have no Beep Codes at all the MoBo might be dead. If this were just a video issue there'd be Beep codes. If there's more than one stick of RAM Pull one try to boot then do same with second stick. if there's only one stick of RAM try reseating it.

the hard drive needs to be replaced

got my phone back hunny xxxxx gia is back agan wraff

Usually replacing the coin cell battery fixes the no boot problem. Look on the motherboard around the processor socket. Electrolytic capacitors can overheat. If you see any of them that are bulging (top is domed instead of flat), they are bad. Trying to replace all the bad ones is tedious and expensive. May be cheaper to replace the motherboard.

What do you mean it does not bring up the monitor?

Your computer is running for sh-- because you probably have too many items starting up at boot time and running in the back ground. You have to go into your msconfig files and services,.msc files to turn off unnecessary operations. And virus programs are notorious for using up memory resources and turning computer into a snail. If you have one, get rid of it and stay off the p-rn sites. It is not the cpu or power supply responsible for the issue. It is the user at fault for overloading the machine's resources. And a new computer will get just as bad if you continue to employ the same habits as you have with this unit.

Hi My cousin had a laptop that ran extremely hot. My solution was to put it up on blocks. Or you can space two books apart, rest the laptop on them and see if the problem goes away.. Two kids Lincoln logs would be perfect. Might save you a trip to the repair shop. Good luck Joe

can you be more specific? why does what keep popping up? If you need further help, reach me via phone at https://www.6ya.com/expert/joel_63c670a84e9f6a97

You're talkign about an emachines computer. If you don't have power.. things to check:Cabling..outlet, etc.. is the outlet is good..cable is good..Next thing to consider, assuming the box hasn't been damaged (lightning/water/etc)... is the powersupply. It's likely a local repair center can check/replace that for you... if its not that, you're in for a new motherboard.. (read--upgrade).. on a positive side..your data should be intact.

please follow the instructions given on the link below https://neosmart.net/wiki/emachines-recovery-disk/

If your computer is less than a year old, you should be able to contact Dell technical support for help (support.dell.com)

It sounds like it's a driver issue - most likely video drivers. You can check the support website for updated drivers for your video card.

How do I upgrade my CPU for emachine e725 ? What are some recommendation such as model number CPU? Intel Pentium Processor T4300 1M Cache 2 10 GHz 800 MHz FSB Teknik Belgeler

if you have the disc that come with your computer get the drivers from there.

You Need To open The CPU(Or tower) to acces the motherboard, the you need to find the CMOS jumper and switch it one spot over the CLR or clear, that will clear the password. If that don't work remove the battery on the motherboard for few seconds then reinstall it. Good luck.