Electrolux Ovens - Page 9 - Recent Questions, Troubleshooting & Support

have a service technician examine the oven and in particular the digital controlled thermostat from what you describe the thermostat setting is not constant (loose connection etc) or faulty digital control unit

If youhave a ELECTROLUX electric Cooker or Fan Ovenwhich is not heating it could be one of the following problems.

1, If the fan motor in theback of the oven is going round and the temperature light is on (normallylittle red light), but there is no heat then you will probably need a new ovenelement, these are generally very easy to fit and readily available from our websitethese can be tested with a electric meter.
To gain access to the ELECTROLUX element you willhave to remove the back plate from inside the oven. Once removed you will seethe fan and element, if you look closely at the element you willprobably see a small hole burnt in it where it has blown. Sometimes howeverthere is no evidence of a fault but the element is opencircuit i.e. broken inside the element casing, either way it will needreplacing. Some elements will are fixed from inside the oven and some are heldin place by nuts from the rear of the machine.

2, If your ELECTROLUXfan oven is getting warm but takes a very long time to cook or is burning thefood more on one side than the other, then you need to check if your oven fan motor isworking you will see the blade turning fast if it is ok. if the element isheating but the fan motor is notblowing the heat into the oven then you need To replace the oven fan motor is alittle more expensive and a bit more involved.
3. If you have the opposite problem i.e. your ovenis over heating and burning everything then you will need to replace your ELECTROLUXoven thermostat

4, A quite common and easily overlooked answer isif your ELECTROLUX oven is not working at all i.e. noheat and no fan then the chances are that someone has put the oven timer into AUTOmode, simply put oven back to MANUAL mode and all should be working again.

You need a 1/4 or 1/16 mm. to take it out, they always have a simgle plug.

Oven Lighting Warning: Risk of electric shock! Prior to changing the oven light bulb: - Switch off the oven! - Disconnect from the electricity supply. Place a cloth on the oven floor to protect the oven light and glass cover. Changing the oven light bulb/cleaning the glass cover 1.Remove the glass cover by turning it anti-clockwise and then clean it. 2.If necessary: replace with 25 watt, 230 V, 300 °C heat-resistant oven lighting. 3.Refit the glass cover. Dado

Far as I know the glass oven door is sealed with special silicone putty that is resistant to a temperature of 300 Celsius . Previously, the required perfect clean the surface with alcohol. Dado

Good Morning Eileen, thank you for your inquiry! I understand that your Electrolux double wall oven is having over heating issues. It is possible that this could be a faulty thermostat, control panel, or element. Since it could be anyone of these underlying having a technician out would help avoid any unnecessary part purchases. If you need help locating a technician you can visit your manufacturer's website for additional assistance with locating a technician. I hope this information is helpful to you. -Matt

To cancel the F10 error, you need to unplug the oven or shut it off at the circuit breaker. Usually this error means that the oven is detecting a runaway temperature. Either the RTD (resistance temperature detector) sensor probe, the electronic oven (EOC) or the wiring is faulty. You can check which one is bad by testing the resistance. The RTD sensor is on the back wall of the oven near the top of the cavity. It's somewhat easier to check the wire at the EOC. Unplug the connector and measure the resistance between the two wires. The resistance should be about 1100 Ohms in a room temperature environment. If you get the incorrect resistance, remove the sensor from the oven and check the resistance at the sensor. If you get the same faulty reading at the sensor and at the EOC, the sensor is probably bad. If the resistance is 1100 Ohms at the sensor, the wiring is bad. If the resistance is correct at all points, the EOC needs to be replaced. Please add a comment with your oven's model number. I will try to find a source with the correct parts. I hope this helps. Cindy Wells

The Electrolux ovens usually used PTC thermistor PT500. Resistance of PTC sensor depending on ambient temperature and should be around 550 ohms on ambient temperatures between 20-30 Celsius. I would like to check insulation rasistance between metalic housing and each connection terminal. The rasistance should be higher than 2 MOhms. Dado

Pull off bottom knob of oven shine torch down at 45degrees u will see a red plate turn off power suply and use a small screwdriver to push the plate turn power back on job done.PS Check all vents are clear to stop it over heating good luck.

Hello Thecarsons, thank you for your post!

I understand that the lock light on your Electrolux range keeps flashing and everything else is working properly. This could be a potential problem with your latch or control panel. I would recommend looking over the latch or strike for any visible damage. If you do not see any, I would suggest performing a reset on your range. You can reset your range by disconnecting the power cord or flipping the household circuit off for at least ten minutes. If that does not resolve your problem you may need to have a technician out to your home to provide a proper diagnosis and repair. This will help you avoid any unnecessary part purchases. -Matt

Electrolux Customer Phone Number Shortest Wait Best Support

• Phone Number

  877-435-3287

• Talk to a Human Press 2 then 1. For kitchen and laundry appliances
• Call Time Average Wait: 37 mins - Monday-Saturday, 8AM-9PM (EST)

Electrolux Calls You Instead Electrolux Calls You Instead I would contact them first before you waste any money.

If you have a problem with your Electrolux EOD5310 cooker or oven then this diagnostic video will help you find the fault and i hope it helps you. i have put a link also so you can get the parts for your cooker cooker parts Need help fixing your appliances these repair guides will also help you find and understand the exact problem with your cooker How to Repair and if we really helped you you could always buy us a beer Buy Paul Beer

Good Morning Gerry, thank you for your inquiry!

I see that your Electrolux oven door will not lock when you attempt to program your self-clean feature. This could be an issue with your door latch or control panel. In order to accurately locate the part needed for the repair of your oven you need to disassemble your oven and test each component. This is not a simple DIY job and I would suggest contacting a technician for proper repairs. They will have the appropriate tools needed for repair. I hope this information is helpful to you. -Matt

I appreciate your post, friend!

I understand that you are having issues with your Electrolux oven not operating properly. From what you have described it sounds like you could have a short within your control panel, keypad, or wiring harness. In order to properly locate the problem and repair it you would need to have the appropriate tools and understanding on how to disassemble your range. This is not a simple DIY job. I would recommend having a professional technician out to perform a proper diagnosis and repair. This will help you avoid any future issues and personal injuries. I hope this information is helpful to you. -Matt

Good Morning Rolf, thanks for your post!

Based off the information you have provided your Electrolux wall oven/microwave combination is stuck in demo mode. The best way to remove demo mode from your wall oven/microwave combo is to hold the oven light button and the on/off keys at the same time and you should be able to toggle in and out of demo mode. Hopefully this is helpful. -Matt

Hello friend, thank you for your inquiry!

I see you are searching for instructions on how to exchange the thermostat on your Electrolux oven. I was unable to locate any step by step instructions from your manufacturer to rewire the thermostat. I would suggest consulting with a professional technician for proper diagnosis and repair. This is not a simple DIY job and incorrect placement of the wires could cause personal injury or future troubles with your oven. Best of luck! -Matt