Edimax Computers & Internet - Popular Questions, Answers, Tips & Manuals

Any router-specific number should be on the router, on a label. To respond, please click the Comment link.

Use torrent.

Find "DMZ" settings and set your ps3 ip there.
It may help you.

Dial router toll free number 1-800-243-0019 to get immediate customer support and services. Get the solution of your router problems. We provide best online support.

open the router page you will the wps pin code skype id :[email protected]

In the "system tray" (the area down near the clock in the lower right-hand corner), you should see an icon that either has bars like on your cell phone, or some kind of icon with waves coming out of it (not the speaker icon). If you don't see an icon like that, then wireless networking is not on. If you do see that icon, click on it, and a list of available networks will pop up. You need to pick the one for your access point. If you didn't change the SSID (network name), then "Edimax AP" should appear on that list. Click on it.

The WAN IP address of your router is assigned by your provider (TelCo, CATV provider, etc.). Most IP addresses are dynamic - which means they can change at any time without notice. When this actually happens is determined by them. It us not unusual to have the same IP address for months at a time however. There is not really something that you can do to make it change outside of contacting them specifically to have them do this for you. LAN address changes are easier - and it is a process you can perform yourself. Do you need instructions for that? Keep in mind that changing a LAN address will not restore connections to a site that has blocked your IP. They have marked your WAN IP and no connection from the local area network (LAN) in your house will be able to connect.

If your Home Hub is a BT type internet hub, then you can connect the WAN port to the Ethernet port on the Hub. This means it will go through two routers. One in the Hub and another in the Edimax. The Edimax needs to be configured as a bridge, because you need to keep within the same address range as the BT router. The Edimax DHCP allocation of IP addresses need to be disabled. This is not on the web site. EDIMAX Technology Official Website Wireless Routers 300Mbps Wireless...

THE SHORT ANSWER IS YES. IF YOU ARE CLOSE ENOUGH TO IT JUST LOG IN TO IT. THE ADDRESS COULD BE 192.168.100.1 OR SOMETHING TO THAT AFFECT.

You need a SSID which is different to the original router, so it needs to have one. But it can be hidden in the configuration, not to be broadcast on the wireless network, so you would have to enter it manually without seeing it in a list. http://us.edimax.com/edimax/mw/cufiles/files/download/manual/transfer/Wireless/EW-7438RPn_Air/EW-7438RPn%20Air_manual.pdf

Most likely paper size is wrong. Push the cont. button on printer. Adjust paper size on trays correctly. Make sure document size is same as paper size esp for PDF and postscript documents

You need to read the manual. There are four different types of 7438RPN extenders. The device needs to be located within the range of the Telstra wireless router, you do not say which router has been provided, so I cannot comment on the set-up of the Telstra router. This is the Air version of the manual. http://us.edimax.com/edimax/mw/cufiles/files/download/manual/transfer/Wireless/EW-7438RPn_Air/EW-7438RPn%20Air_manual.pdf

Find its ip number, use web site. Go to ip number and you can delete the old router. Then it should pick up your new router just fine.

You need to contact technical support who could supply a copy of the original firmware, which you could re-install, over the upgrade. ? necessario contattare il supporto tecnico che potrebbe fornire una copia del firmware originale, che si potrebbe ri-installare, sopra l'aggiornamento. Support Services

You need to download the manual for this Middle East version of the access point/ wireless extender. Page 4 covers resetting the router so a new password can be put in. http://us.edimax.com/edimax/mw/cufiles/files/download/manual/transfer/Wireless/EW-7206APg/EW-7206APg_PDg-Manual-EN.zip If you press and hold the reset button for more than 4 seconds, the Access Point will reset to the factory defaults (Warning: Your settings will be deleted and replaced with the factory default settings).

Hello, my name is Glenn, I am not familiar with wireless signal boosters, but I have a great idea on how to set up networks and multiple routers in 1 network. How I picture a wireless signal booster to work is to plug in from your netgear router, into the Edimax.

WK-1074 is not listed as a EDIMAX router. Contact technical support is you think this is wrong. EDIMAX Technology

If you have checked all of the cords, you can try and see if a reset works. There should be a small hole on the rear of the unit. Insert a pin or paper lip and hold. You will hopefully see lights blink. If you do not, it is likely dead. Consort manufacturers warranty, though it is unlikely, you may be covered for a replacement.

Use an ethernet cable.

On the back of the router.