E-Machines W - Recent Questions, Troubleshooting & Support - Page 7

try replacing all the leads that attach to your hard drive including electrical extensions IDE,SATA and the ones that attach from your motherboard to hard drive hope this helps

You didn't mention up to where is the display. There are cases that this is cause by corrupted operating system (reistall OS) and defective memory modules. You can remove your memory module and reinstall again (one at a time if you have more than one module).
Good luck

TedMac

there is marking in each wire which pin need to be inserted??

here is driver link for your phone
click on it & download
http://direct.motorola.com/hellomoto/in/support/driversNplugins.asp?country=aus&language=ena#

http://restore-disk.com/restoredisks/eMachines/eMachinesW2686/eMachines-W2686-Vista-Restore-Disk-255089.html

http://www.user-guides.co.uk/eMachines/eMachinesRecovery/eMachines.asp?keywords=eMachines+eMonster+XP+Recovery+CD+Disk&recor=1

http://www.restoredisks.com/?gclid=CM6j04nh4aMCFRr6iAoddFklfA

hope this helps

Open cpu cabinet then you can motherboard pull cmos cell from motherboard for 10 seconds then put it back reconnect RAM memory reconnect both connection to harddrive .Make sure motherboard is not ground with cabinet. Then check. Also when you power up the computer press F8 key 5 to 6 times then if you are able to see safe mode and other menu enter in "Enable vga mode" then go to display property and change screen resolution to 1024*768 then apply. Let me know if you need further assistance. Thanks for using FixYa.

Your machine supports, DDR2 SDRAM or (DDR2) type Ram, maximum 2GB and has two Ram Slots.

Good luck.

Thanks for using FixYa.

Hmm, low or high doesn't make much difference. Here is the specs on your memory from Kingston.

http://tinyurl.com/2faq8uv

Please go through the link and download appropriate drivers http://downloadcenter.intel.com/SearchResult.aspx?lang=eng&ProductFamily=Graphics&ProductLine=Desktop+graphics+controllers&ProductProduct=Intel%c2%ae+82845G+Graphics+Controller

Let try booting your computer to Last known good configuration, to do this follow this steps.
Power OFF the computer and then power it back ON and once you hear the beep sound press F8 key and that will load up advance boot menu and from that you will see there Safe Mode and other options look for Last Known Good Configuration and select that and select your operating system and then hit enter computer will load and if that one work fine you should be now back with the computer working again.

Not sure that this is what you need, but should work. If you have Windows OS, try pressing F8 when booting. A menu will be given on the screen. Will have to choose SAFE MODE and when windows loads go to START MENU-PROGRAMS-ACCESSORIES-SYSTEM TOOLS and choose SYSTEM RESTORE

Try this : See if you can find your motherboard model number. If so, type it into Google, go to the manufacturers site and download a manual which should have the wiring diagram you require. 
Cheers.

mcdevito75 here, Best Bet, contact your internet provider, the people that provide your email are the internet provider, as example, AOL, netzero.

it may be a problem of hard drives jumper settings and the CMOS/BIOS setting conflicts!!
first try to go to setup on pressing F2 and load optimal values and restart!!
if this does not help then open the CPU and see the hard drives jumper settings and make it to chip select(CS), and restart!
this mainly will be the problems!

reply and rate!!!

sounds to me like its suffering from a commen problem with the e machines the motherboard has gone and needs replacing hope this helps

You can download the driver from E-Machine's support site and then burn them to a CD with a burning program.

http://www.emachines.com/support/drivers.html

Emachines are noted if they don't boot up the mother board has gone bad. Also the power unit goes bad on most models taking the motherboard with it as well. I have two setting around as parts units now the parts few years and have inquired into many websites about these PC's. I was told to replace them instead of repairing them for the money. I hope you will investigate my findings as well
Laptops are the way to go now a days for they are easy to move around and the power packs are under $10 to replace. Lap tops are even at the $300 range these days at Wall Mart too

I am providing you with the link from where you can download it and if you are not satisfied then you have to buy a one

http://www.freedownloadscenter.com/Utilities/Backup_and_Copy_Utilities/RestoreIT.html

Please rate me if this solution works for you

Thanks......Have a great time

Make sure your "CD" is readable. In other words a CD-ROM will not read a DVD.

Also, is this "CD" in retail format or is it a burned CD or a CD that someone made for you? If that is the case, then your computer may not be able to read the "CD".

Thanks.