E-Machines T - Popular Questions, Answers, Tips & Manuals - Page 5

Try another monitor to verify the Graphics Card, if you have a graphics card, then another monitor cable. check for bent pins in the connectors, eliminate the hardware by changing each component/cable one by one. It may be the Graphics Card/Adapter is gone. Clean the inside of machine, overheating due to dust will cook components, GPU's get quite hot. Try some Electronic Contact cleaner spray on the Graphics Card connections, if applicable. Unplug before reseating the Graphics Card or cleaning, take precautions in ESD before handling a Component. If your Graphics is integrated, you can purchase a aftermarket PCIe x16 Graphics Card quite reasonably, : http://www.google.com/webhp?source=search_app#q=ati+amd+pcie+x16+graphics+card&hl=en&sa=X&tbs=vw:l,p_ord:p&tbm=shop&ei=ze05Uf25KJDO9ASIyYHYDw&ved=0CF8Quw0oAg&bav=on.2,or.r_qf.&bvm=bv.43287494,d.eWU&fp=bc2048b0dd90d6d4&biw=854&bih=580

Yes as long as your T6520 comes with at least a 400 watt power supply. It has the required 16x PCI Express slot.

At power on, enter the bios (usually by tapping a function key like Tab or Del or F2) and change the boot device order to have the CD drive first. Put the disc in the disc drive. Save and continue. Now, you may get a message asking you to "press any key to boot to the CD". Touch any key, and the reload should start. See... http://pcsupport.about.com/od/fixtheproblem/a/biosaccess_pc.htm

Front or Rear connections? Open the case, it's at the rear of the Mobo. It will be enclosed in the connectors. If you have lost a channel, it may not be easy to repair. A sound card is a option.

what?

weak DVD drive

just go to facebook.com to resign up

Open Control Panel, Device Manager, Sounds, Is the audio device listed? Enabled? The Windows XP drivers can be found here, install and reboot: http://support.gateway.com/us/en/emac/product/default.aspx?modelId=1645

search for a special software : cpu fan speed control

Replace Hard drive and Re-Install the Operating System.

Suggest you remove the Ram Memory modules, ('Stick'), and clean the gold plated contact pins. Then reinstall.The beeps you hear are BIOS Beep Codes. The computer's way of telling you something is wrong, and an area to look into for it.2 short beeps indicate a memory problem.The eMachines T6528 uses an MSI MS-7207 motherboard.(Micro Star International)Otherwise known as the MSI K8NGM2-FID /IL / L,http://www.msi.com/product/mb/K8NGM2-FID--IL--L.htmlUses DDR Sdram ram memory.(Either 266MegaHertz, 333MHz, or 400MHz. Which is PC-2100, PC-2700, and PC3200; respectively)http://en.wikipedia.org/wiki/File:Generic_DDR_Memory_%28Xytram%29.jpgHandle the Ram Memory by the BODY. The Body is everywhere on the ram memory module, Except the gold plated contact pins at the Bottom.The Body is coated with a see-through protective plastic.Use a pencil eraser to clean the gold plated contact pins.If you are using an eraser on the end of a pencil, and not a solid eraser; refrain from letting the metal band touch, the gold plated contact pins.Rub across all contact pins, (BOTH sides), and up, and down on them. You don't have to use too much pressure.Once finished use air to remove the eraser dust.You can use a can of compressed air for computers, if available; or air pressure from your mouth will be sufficient.(Humans can deliver up to 20 pounds of air pressure)Reinstall.BEFORE you reach inside your computer, FOLLOW Anti-Static Precautions.Your body carries Static electricity. Static WILL fry out (Short Circuit), the delicate hardware components inside a computer.Relieve your body of Static.Computer ON a table, computer unplugged from power, computer case open;TOUCH an unpainted surface, of the metal frame of the open computer case.This action will relieve your body of Static.IF you leave your computer in the middle of working on it, be SURE to Touch the metal frame again upon your return.Use a can, or two of compressed air for computers. You may wish to wear a dust mask also.For additional questions please post in a Comment.Regards,joecoolvette[If this doesn't 'cure' the problem, we will diagnose further ]

That Machine would take DDR2 PC2-5300 upgrade chips. The max that system could take would be two 1GB sticks for a total of 2GB or 2048MB of memory. Memory is fairly easy to damage with static discharge and is also very easy to not put in all the way. When putting it in, unplug the power from the computer, push and hold the power button for 20-30 seconds to help discharge power from the computer, Line up the pins on the memory and push them into place till the little arms at the sides of the slot pop up and click into place. I'd install one chip at a time, powering the machine up after the first chip to make sure it works, then starting over again. The only time I'd install both chips at the same time would be when installing a memory kit (two or more chips in one package), in which case, install both chips before powering it on.

Wrong websiteRegards,joecoolvette

Can you remove the front cover, access the rear of the button, clean, use silicon spray/ repair. Sometimes the plastic retainer/spring will break and not return the button to the out position.

If you go to the eMachines website you can download an owners manual off of the site for your system. Hope that this helps..

Power source is more than likely dead. :p You will need to replace it, but it's best to take it into a shop since these things require troubleshooting. There could be multiple reasons why it won't start.

http://support.gateway.com/us/en/emac/product/default.aspx?tab=1&modelId=1537Or is there something I'm missing by the reference - Retail?All the drivers I pulled up are XPx86.Means XP and 32-bit version.What drivers do you need? Post back in a Comment.The eMachines T2899 Desktop PC uses an FIC AU31 motherboard.(First International Computers)Also known as the K7M-NF18G.This is the download link to the motherboard manual,http://www.elhvb.com/mboards/OEM/eMachines/manuals/index.htmlClick on the blue - FIC AU31 - in the left column.Regards,joecoolvette

Hard boot. Unplug it.

WARNING: Before you start troubleshooting remember that you are dealing with electricity that can KILL. http://www.kitchentablecomputers.com/static.php - rules Only work inside the computer case when the power has been switched off and disconnected. Never open the power source. Some of the below steps recommend removing physical parts within the computer. While in the computer it is highly recommend that you be aware of ESD and its potential hazards Test all leads that attach to your hard drive including electrical extensions IDE SATA the leads from your ((motherboard to your hard drive)) make sure they have secure dust free connections and are not faulty or just replace them they might be faulty if its a 40 pin flat ribbon type it will be the first to fail make sure all leads that are attached to your drives dvd\cd 3 1/2 inch floppy have secure dust free connections and are not faulty even something as small as an electrical fan and its lead can cause you problems computers need all power and data to continue through every working device and to have an end so any faulty leads will end up with a computer error make sure your graphics card is securely seated with no dust built up or in the socket if you remove your graphics check the socket to make sure its dust free restart your computer then reinstall it this should activate found new hardware wizard or you might try You will need to connect to another monitor or your television to your computer with the vga lead monitor connection. Click start control panel display change display settings adjust resolution this may vary depending on your operating system You should see a no 1 and a no 2 with detect and identify keep an eye on the screen when you select the number tabs this may vary depending on your operating system when you select the no 2 tab this should be the extended desktop always click apply after making any changes. If you can get an extended desktop your monitor is faulty if you cant get an exended desktop Hope this helps.

Hi and welcome to fixya firstly check your power cable of the CPU and then if this isn't works then put the RAM from the CPU and then reinsert it if still isnt work then there should b a hardware problem